manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DIAGNOSTIC PROCEDURE 

DTC P0604 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

CONDITION

 

POSSIBLE CAUSE

 

z

Module reprogramming  

z

Aftermarket performance products.  

z

PCM malfunction  

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 

HAS BEEN RECORDED.

 

z

Has FREEZE FRAME DATA 
been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 

repair order, then go to the next step.

2

VERIFY RELATED REPAIR 
INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

Yes

Perform repair or diagnosis according to 
the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

No

Perform PCM reprograming using the M-
MDS, then go to next step.

3

VERIFY TROUBLESHOOTING OF 

P0604 HAS BEEN COMPLETED

 

z

Verify that all disconnected 
connectors are reconnected.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Perform the "KOEO and KOER 

self-test". 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 

DTC present?  

Yes

Replace the PCM, go to the next step. 

(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

4

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "After Repair 

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:34 AM

Page 284 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

NavLinkz CAM-N-CV133-V Manual preview
CAM-N-CV133-V
Brand: NavLinkz Pages: 4
Ford F-150 2018 Quick Reference Manual preview
F-150 2018
Brand: Ford Pages: 12
Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Brand: Jeep Pages: 1311
Atwood Lippert Components LEVELEGS MPD 66385 Manual preview
Lippert Components LEVELEGS MPD 66385
Brand: Atwood Pages: 6
BMW 65 41 2 152 528 Installation Instructions Manual preview
65 41 2 152 528
Brand: BMW Pages: 21
Cadillac Escalade ESV 2014 Owner'S Manual preview
Escalade ESV 2014
Brand: Cadillac Pages: 508
Hama Liberty III Quick Start Manual preview
Liberty III
Brand: Hama Pages: 2
Draw tite 24943 Installation Instructions preview
24943
Brand: Draw tite Pages: 4
Mercedes-Benz CLS 280 2008 Owner'S Manual preview
CLS 280 2008
Brand: Mercedes-Benz Pages: 329
Volvo 164 1969 Service Manual preview
164 1969
Brand: Volvo Pages: 266
Pacbrake HP10098 Installation Manual preview
HP10098
Brand: Pacbrake Pages: 6
Bestop 614.04 Installation Manual preview
614.04
Brand: Bestop Pages: 31
Quadratec QuadraTop 11051.0415 Installation Manual preview
QuadraTop 11051.0415
Brand: Quadratec Pages: 8
Packard 1948 eight Operating Instructions Manual preview
1948 eight
Brand: Packard Pages: 25
ADS FlashLogic FLC-FORS-FO1B-FLRSFO1-EN Install Manual preview
FlashLogic FLC-FORS-FO1B-FLRSFO1-EN
Brand: ADS Pages: 25
Mercedes-Benz W211 Manual preview
W211
Brand: Mercedes-Benz Pages: 27
Chevrolet El Camino 1983 Owner'S Manual preview
El Camino 1983
Brand: Chevrolet Pages: 103
Peak PKC0BJ Owner'S Manual preview
PKC0BJ
Brand: Peak Pages: 8

Brands by name

Popular brands

Load more brands