manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P1635 [MZI-3.5] 

DTC P1635 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

DIAGNOSTIC PROCEDURE 

DTC P1635 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

PROCEDURE

 

z

Perform the "AFTER REPAIR 

PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P1635

Tire/axle out of acceptable range

DETECTION 

CONDITION

 

z

This DTC indicates the tire and axle information contained in the vehicle 
identification block does not match the vehicle hardware.  

POSSIBLE CAUSE

 

z

Incorrect tire size  

z

Incorrect axle ratio  

z

Incorrect vehicle identification configuration parameters  

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 

HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 

been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 

repair order, then go to the next step.

2

VERIFY RELATED REPAIR 
INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 
and/or on-line repair information 

availability.  

z

Is any related Service Bulletins 
available?  

Yes

Perform repair or diagnosis according to 
available Service Bulletins. 

z

If vehicle is not repaired, go to the 
next step.  

No

Go to the next step.

3

VERIFY VEHICLE 

IDENTIFICATION TIRE DATA

 

z

Turn the ignition switch to the ON 

position.  

z

Connect the M-MDS to the DLC-

Yes

Go to the next step.

No

Perform PCM configuration procedure, 
then go to Step 5. (see 

PCM 

CONFIGURATION [MZI-3.5]

 .)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:37 AM

Page 378 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Baja Designs S8 Instructions Manual preview
S8
Brand: Baja Designs Pages: 6
Jacob Jensen Electronic Parking Disc II User Manual preview
Electronic Parking Disc II
Brand: Jacob Jensen Pages: 28
FABBRI PORTATUTTO 17405400 Assembly Instructions preview
17405400
Brand: FABBRI PORTATUTTO Pages: 2
Mobis G4211ADE00AL Installation Instructions Manual preview
G4211ADE00AL
Brand: Mobis Pages: 16
Subaru starlink Manual preview
starlink
Brand: Subaru Pages: 216
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Brand: APS Auto Parts Specialist Pages: 3
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Brand: Metra Electronics Pages: 2
Whispbar K925W Fitting Instructions Manual preview
K925W
Brand: Whispbar Pages: 15
TATA Motors tigor Owner'S Manual preview
tigor
Brand: TATA Motors Pages: 159
BrandMotion FLTW-7690 Installation Instructions preview
FLTW-7690
Brand: BrandMotion Pages: 2
Jeep PATRIOT 2013 Manual preview
PATRIOT 2013
Brand: Jeep Pages: 16
Audi RSE III Quick Start Manual preview
RSE III
Brand: Audi Pages: 4
Whispbar K607W Fitting Instructions Manual preview
K607W
Brand: Whispbar Pages: 14
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Brand: Ecco Pages: 24
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Brand: Rugged Ridge Pages: 3
Camoplast T4S Installation Manuallines preview
T4S
Brand: Camoplast Pages: 19
Oldsmobile 1998 Aurora Owner'S Manual preview
1998 Aurora
Brand: Oldsmobile Pages: 380
WABCO TEBS E Manual preview
TEBS E
Brand: WABCO Pages: 224

Brands by name

Popular brands

Load more brands