manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

If the spool valve is stuck in advance direction, replace the OCV. (see 

OIL CONTROL VALVE 

(OCV) REMOVAL/INSTALLATION [MZI-3.5].

 )  

2. Connect the OCV.  
3. Turn the ignition switch to ON position.  
4. Verify that the spool valve is at max. retard position. 

z

If the spool valve is stuck in advance direction, inspect the following: 

„

Short circuit in harnesses or connectors between the OCV and the PCM.  

5. Inspect the variable valve timing actuator.  

When idling can be continued

  

For right bank

  

1. Disconnect OCV (RH) connector.  
2. Warm up the engine and it at idle.  
3. Apply the battery voltage to the OCV and verify that the engine idles roughly or stalls. 

z

If the engine idles roughly or stalls, inspect the timing belt component (valve timing deviation).  

z

If the engine does not idle roughly or stall, go to the next step.  

4. Remove the OCV (RH) and perform spool valve operation inspection. (see 

OIL CONTROL VALVE 

(OCV) REMOVAL/INSTALLATION [MZI-3.5].

 ) 

z

If not as specified, inspect the following: 

„

OCV (RH)  

„

Harnesses and connectors between OCV (RH) and PCM have an open or short circuit.  

z

If as specified, inspect the following right bank hydraulic passages for clogging or leakage, or both. 

„

Oil pressure switch - OCV  

„

OCV - camshaft  

„

Camshaft internal passage  

5. If they are normal, replace the right bank camshaft pulley (with built-in variable valve timing actuator).  

When idling can be continued

  

For left bank

  

1. Disconnect OCV (LH) connector.  
2. Warm up the engine to idle.  
3. Apply the battery voltage to the OCV and verify that the engine idles roughly or stalls. 

z

If the engine idles roughly or stalls, inspect the timing belt component (valve timing deviation).  

z

If the engine does not idle roughly or stall, go to the next step.  

4. Remove the OCV (LH) and perform spool valve operation inspection. (see 

OIL CONTROL VALVE 

(OCV) REMOVAL/INSTALLATION [MZI-3.5].

) 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:38 AM

Page 111 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Ecco Gemineye EC2014-C Installation Instructions Manual preview
Gemineye EC2014-C
Brand: Ecco Pages: 10
Ecco Reflex 5500 Series Installation And Operating Instructions Manual preview
Reflex 5500 Series
Brand: Ecco Pages: 12
Parrot CK 3000 Evolution Specifications preview
CK 3000 Evolution
Brand: Parrot Pages: 2
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Brand: BMW Pages: 160
PEUGEOT Partner Origin Handbook preview
Partner Origin
Brand: PEUGEOT Pages: 128
Schumacher Electric SPI6 Owner'S Manual preview
SPI6
Brand: Schumacher Electric Pages: 87
Cadillac 2009 ESCALADE ESV Owner'S Manual preview
2009 ESCALADE ESV
Brand: Cadillac Pages: 602
Caltrend CV445 Installation Instructions preview
CV445
Brand: Caltrend Pages: 2
Audiovox EM-2201 Installation Instructions preview
EM-2201
Brand: Audiovox Pages: 1
EGR EGR-3PVE-COLOUR Installation Instructions Manual preview
EGR-3PVE-COLOUR
Brand: EGR Pages: 28
Gator HUDGPS1 Quick Start Manual preview
HUDGPS1
Brand: Gator Pages: 2
Hummer 2006 H2 Owner'S Manual preview
2006 H2
Brand: Hummer Pages: 502
TATA Motors Tata Indigo Diesel Owner'S Manual & Service Book preview
Tata Indigo Diesel
Brand: TATA Motors Pages: 190
Safe Fleet Prime Design HBR-E-FT33B Assembly Instructions Manual preview
Prime Design HBR-E-FT33B
Brand: Safe Fleet Pages: 12
Subaru 360 Sedan Service Manual preview
360 Sedan
Brand: Subaru Pages: 16
Road Ranger H392 Installation Manual preview
H392
Brand: Road Ranger Pages: 22
Pyle PLDCP3 User Manual preview
PLDCP3
Brand: Pyle Pages: 2
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112

Brands by name

Popular brands

Load more brands