Mazda CX-9 Grand Touring 2007 Manual Download Page 697

Page: 697 / 1056

DTC P1288 [MZI-3.5]

DTC P1288 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

DIAGNOSTIC PROCEDURE

DTC P1288 (MZI-3.5) DIAGNOSTIC PROCEDURE

Is there any malfunction?

VERIFY TROUBLESHOOTING OF
DTC P1285, P1299 HAS BEEN

COMPLETED

Verify that all disconnected
connectors are reconnected.

Turn the ignition switch to the ON

position (Engine off).

Clear the DTC from the PCM

memory using the M-MDS.

Start the engine and run it at idle.

Retrieve DTCs using the M-MDS.

Is the PENDING CODE for this
DTC present?

Yes

Replace the PCM, then go to the next step.
(see

PCM

REMOVAL/INSTALLATION [MZI-
3.5]

Go to the next step.

VERIFY AFTER REPAIR

PROCEDURE

Perform the "AFTER REPAIR

PROCEDURE".

(See

AFTER REPAIR

PROCEDURE [MZI-3.5]

Are any DTC present?

Yes

Go to the applicable DTC inspection.

(See

DTC TABLE [MZI-3.5]

Troubleshooting completed.

DTC P1288

CHT sensor out of self-test range

DETECTION
CONDITION

Indicates the CHT sensor is out of self-test range. The engine is not at a
normal operating temperature.

POSSIBLE CAUSE

Cold engine

Engine overheating

Connector or terminal malfunction

Low engine coolant level

CHT sensor malfunction

STEP

INSPECTION

ACTION

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:36 AM

Page 350

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands