Mazda CX-9 Grand Touring 2007 Manual Download Page 279

Page: 279 / 1056

8. Rotate the crankshaft clockwise until the keyway is in the 11 o'clock position. (This will position the No.1

cylinder at TDC.)

9. Follow the "TIMING CHAIN REMOVAL/INSTALLATION" procedure and install the timing chain.

(See

TIMING CHAIN REMOVAL/INSTALLATION [MZI-3.5]

10. Remove the

SSTs

installed to the camshaft components on both banks.

Fig. 140: View Of Crankshaft Keyway At 11 O'Clock Position

Courtesy of MAZDA MOTORS CORP.

OIL CONTROL VALVE (OCV) REMOVAL/INSTALLATION [MZI-3.5]

1. Disconnect the negative battery cable.
2. Remove the engine cover. (See

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

3. Remove the ventilation hose. (see

QUICK RELEASE CONNECTOR (EMISSION SYSTEM)

REMOVAL/INSTALLATION [MZI-3.5].

)

4. Disconnect the vacuum hose. (see

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.5]

5. Remove the resonance chamber. (see

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.5]

6. Remove the dynamic chamber and throttle body as a single unit. (see

INTAKE-AIR SYSTEM

REMOVAL/INSTALLATION [MZI-3.5]

7. Disconnect the wiring harness.
8. Remove the ignition coils. (see

IGNITION COIL REMOVAL/INSTALLATION [MZI-3.5]

9. Remove the dipstick.

10. Remove the cylinder head cover. (See

TIMING CHAIN REMOVAL/INSTALLATION [MZI-3.5]

11. Remove the OCV.

Tightening torque

8.5-11.5 N.m {87-117 kgf.cm, 76-101 in.lbf}

NOTE:

The LH side is shown, however, the RH side is the same.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:28 AM

Page 88

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands