manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

If there is oil leakage, repair or replace the applicable part.  

11. Inspect the oil level. (See 

ENGINE OIL LEVEL INSPECTION [MZI-3.5]

.)  

12. Inspect for engine coolant leakage. (see 

ENGINE COOLANT LEAKAGE INSPECTION [MZI-3.5]

.) 

Fig. 6: Identifying Water Hose, Oil Cooler And O-Ring With Torque Specifications

 

Courtesy of MAZDA MOTORS CORP.

 

OIL COOLER INSTALLATION NOTE 

1. Tighten the oil cooler bolts in the order shown in the figure. 

Fig. 7: Tightening Oil Cooler Bolts With Tightning Sequence

 

Courtesy of MAZDA MOTORS CORP.

 

OIL PAN REMOVAL/INSTALLATION [MZI-3.5] 

WARNING:

z

Fuel vapor is hazardous. It can very easily ignite, causing serious 

injury and damage. Always keep sparks and flames away from fuel.  

z

Fuel line spills and leakage are dangerous. Fuel can ignite and cause 

serious injures or death and damage. Fuel can also irritate skin and 
eyes. To prevent this, always complete the "Fuel Line Safety 

Procedure". (see BEFORE REPAIR PROCEDURE [MZI-3.5] .)  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE Lubrication (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:32:53 AM

Page 7 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Jeep Renegade Owner'S Handbook Manual preview
Renegade
Brand: Jeep Pages: 212
Jacob Jensen Electronic Parking Disc 3 Quick Manual preview
Electronic Parking Disc 3
Brand: Jacob Jensen Pages: 2
Yakima K1005 Instructions Manual preview
K1005
Brand: Yakima Pages: 12
Napoli NPL-TV 7874 DIGITAL Instruction Manual preview
NPL-TV 7874 DIGITAL
Brand: Napoli Pages: 20
Paccar DAF POWERCHOICE 250A Installation Manual preview
DAF POWERCHOICE 250A
Brand: Paccar Pages: 20
Romik 2137 2D Installation Instructions Manual preview
2137 2D
Brand: Romik Pages: 6
REVCAMUK MON16AHD Instructions preview
MON16AHD
Brand: REVCAMUK Pages: 4
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
Whispbar K607W Fitting Instructions Manual preview
K607W
Brand: Whispbar Pages: 14
Whispbar K919W Fitting Instructions Manual preview
K919W
Brand: Whispbar Pages: 17
Paccar DAF CHARGEMAX 90 User Manual preview
DAF CHARGEMAX 90
Brand: Paccar Pages: 40
Saab 9000 1985 Service Manual preview
9000 1985
Brand: Saab Pages: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Brand: A-rival Pages: 23
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Brand: Mont Blanc Pages: 2
Toyota Avalon 2001 Operating Manual preview
Avalon 2001
Brand: Toyota Pages: 295
Griffin Technology iTrip Bluetooth User Manual preview
iTrip Bluetooth
Brand: Griffin Technology Pages: 6
Mitsubishi Pajero Pinin 1999 Workshop Manual preview
Pajero Pinin 1999
Brand: Mitsubishi Pages: 919
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Brand: RAM Pages: 360

Brands by name

Popular brands

Load more brands