manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

Fig. 4: Fuel System Diagram

 

Courtesy of MAZDA MOTORS CORP.

 

BEFORE REPAIR PROCEDURE [MZI-3.5] 

FUEL LINE SAFETY PROCEDURE 

1. Remove the fuel-filler cap and release the pressure in the fuel tank.  
2. Disconnect the negative battery cable. (see 

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

 .)  

3. Remove the fuel pump relay.  
4. Connect the negative battery cable. (see 

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

.) 

WARNING:

z

Fuel vapor is hazardous. It can easily ignite, causing serious injury 

and damage. Always keep sparks and flames away from fuel.  

z

Fuel line spills and leakage are dangerous. Fuel can ignite and cause 

serious injuries or death and damage. Fuel can also irritate skin and 
eyes. To prevent this, always complete the following "Fuel Line 

Safety Procedure".  

z

A person charged with static electricity could cause a fire or 

explosion, resulting in death or serious injury. Before performing 
work on the fuel system, discharge static electricity by touching the 

vehicle body.  

NOTE:

z

Fuel in the fuel system is under high pressure also when the engine is not 

running.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Fuel System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:24:12 AM

Page 4 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

IBASE Technology MPT-3000V User Manual preview
MPT-3000V
Brand: IBASE Technology Pages: 100
Modifry Products S2000 Windscreen Camera Mount Quick Start Manual preview
S2000 Windscreen Camera Mount
Brand: Modifry Products Pages: 2
Alpitronic Hypercharger HYC 075 Operation Instructions And Installation Manual preview
Hypercharger HYC 075
Brand: Alpitronic Pages: 64
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Brand: Dakota Digital Pages: 3
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Brand: Safe Fleet Pages: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Brand: Honda Pages: 4
Thetford SANICON TURBO 300 Operating Instructions Manual preview
SANICON TURBO 300
Brand: Thetford Pages: 25
JBL smartbase Quick Start Manual preview
smartbase
Brand: JBL Pages: 12
Cadillac 2011 SRX CROSSOVER Owner'S Manual preview
2011 SRX CROSSOVER
Brand: Cadillac Pages: 416
TIE DOWN LONGRUN 86103 Assembly/Installation Instructions preview
LONGRUN 86103
Brand: TIE DOWN Pages: 2
Columbia THERAPEDIC 2000 Instructions For Use Manual preview
THERAPEDIC 2000
Brand: Columbia Pages: 14
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Brand: DEFA Pages: 28
Steelmate PTS800V7 User Manual preview
PTS800V7
Brand: Steelmate Pages: 14
Prorack K577W Fitting Instructions Manual preview
K577W
Brand: Prorack Pages: 15
Mazda 0000-8L-G03A Installation Instructions preview
0000-8L-G03A
Brand: Mazda Pages: 3
Mobileye C2-270 User Manual preview
C2-270
Brand: Mobileye Pages: 29
Ford TRANSIT CUSTOM Quick Reference Manual preview
TRANSIT CUSTOM
Brand: Ford Pages: 15
Honda 08L04-SZA-100 Installation Instructions preview
08L04-SZA-100
Brand: Honda Pages: 3

Brands by name

Popular brands

Load more brands