Mazda CX-9 Grand Touring 2007 Manual Download Page 840

Page: 840 / 1056

Connect the M-MDS to the DLC-2.
Do the following conditions appear?

The engine is not completely
started.

DTC P1260 is displayed.

Yes

Both conditions appear:

Go to Step 3.

Either or other condition appears:

Go to the next step.

Does the engine stall after

approx. 2 s

since the engine is started?

Yes

Go to the next step.

Immobilizer system is normal.
Go to Step 8.

Is coil connector securely connected to

coil?

Yes

Go to the next step.

Connect the coil connector securely.

Return to Step 2.

Does the security light flush?

Yes

Go to the next step.

Inspect and repair or replace the

following:

Wiring harnesses and connectors

from keyless control module
terminal 3W and instrument

cluster terminal 1W

Wiring harness and connectors
from keyless control module

terminal 3X and instrument cluster
terminal 1X

Instrument cluster

(see

INSTRUMENT CLUSTER

INSPECTION

Connect the M-MDS to the DLC-2 and
retrieve DTC for PCM, instrument

cluster and keyless control module
(with advanced keyless entry system).

Are any of the following DTCs
displayed?

DTC

PCM: B1342, U0073, U0155

Instrument cluster: B1213, B1600,
B1601, B1602, B1681, B2103, 2139,

B2431, U0110, U0214

Keyless control module (with

advanced keyless entry system):
B1681, B2103, B1213

Yes

Go to the appropriate DTC inspection.
(see

DTC TABLE [MZI-3.5]

Go to the next step.

Inspect for the following wiring

harnesses and connectors:

Yes

Repair or replace the suspected wiring

harness and connector.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:36 AM

Page 23

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands