manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

Turn the ignition switch off.  

z

Disconnect PCM connector.  

z

Inspect for poor connection (such 
as damaged/pulled-out pins, 

corrosion).  

z

Is there any malfunction?  

No

Go to the next step.

8

INSPECT PURGE SOLENOID 
VALVE CONTROL CIRCUIT FOR 

OPEN CIRCUIT

 

z

Turn the ignition switch off.  

z

Inspect continuity between purge 

solenoid valve terminal B and 
PCM terminal 1BC.  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 
the Step 10.

9

INSPECT PURGE SOLENOID 

VALVE

 

z

Inspect the purge solenoid valve. 

(see 

PURGE SOLENOID 

VALVE INSPECTION [MZI-
3.5]

 .) 

z

Is there any malfunction?  

Yes

Replace purge solenoid valve 

(see 

PURGE SOLENOID VALVE 

REMOVAL/INSTALLATION [MZI-

3.5]

 .), then go to Step 10.

No

Go to the next step.

10

VERIFY TROUBLESHOOTING OF 
DTC P0443 COMPLETED

 

z

Make sure to reconnect all 
disconnected connectors.  

z

Clear DTC from PCM memory 

using M-MDS.  

z

Perform the "KOEO or KOER 
self-test" using the M-MDS. 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Is the PENDING CODE same 

DTC present?  

Yes

Replace PCM, then go to the next step. 
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

11

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "AFTER REPAIR 

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:33 AM

Page 221 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Jeep Automobile Service And Warranty Handbook preview
Automobile
Brand: Jeep Pages: 42
Jeep Automobile Warranty Information Booklet preview
Automobile
Brand: Jeep Pages: 44
Cadillac ATS 2015 Convenience/Personalization Manual preview
ATS 2015
Brand: Cadillac Pages: 20
Jeep Automobile Service Contract preview
Automobile
Brand: Jeep Pages: 7
Cadillac 2016 ELR Convenience/Personalization Manual preview
2016 ELR
Brand: Cadillac Pages: 20
Cadillac 2016 CTS Manual preview
2016 CTS
Brand: Cadillac Pages: 354
Cadillac 2005 CTS Personalization Manual preview
2005 CTS
Brand: Cadillac Pages: 20
Cadillac 2014 XTS Convenience/Personalization Manual preview
2014 XTS
Brand: Cadillac Pages: 20
Cadillac ATS 2014 Specifications preview
ATS 2014
Brand: Cadillac Pages: 10
Cadillac 2013 Escalade ESV Owner'S Manual preview
2013 Escalade ESV
Brand: Cadillac Pages: 524
Cadillac 2013 ATS Personalization Manual preview
2013 ATS
Brand: Cadillac Pages: 20
Cadillac ATS 2013 Owenrs Manual preview
ATS 2013
Brand: Cadillac Pages: 438
Cadillac 2013 ATS Owner'S Manual preview
2013 ATS
Brand: Cadillac Pages: 450
Cadillac 2011 Escalade Hybrid Owner'S Manual Addendum preview
2011 Escalade Hybrid
Brand: Cadillac Pages: 94
Cadillac 2011 Escalade Hybrid Owner'S Manual preview
2011 Escalade Hybrid
Brand: Cadillac Pages: 94
Cadillac 2011 CTS COUPE Navigation Manual preview
2011 CTS COUPE
Brand: Cadillac Pages: 78
Cadillac 2011 CTS COUPE Brochure preview
2011 CTS COUPE
Brand: Cadillac Pages: 8
Cadillac 2010 Escalade Manual preview
2010 Escalade
Brand: Cadillac Pages: 113

Brands by name

Popular brands

Load more brands