manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DIAGNOSTIC PROCEDURE 

DTC P0685 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 
HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 
been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 
repair order, then go to the next step.

2

VERIFY RELATED REPAIR 

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

Yes

Perform repair or diagnosis according to 

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

No

Go to the next step.

3

INSPECT MAIN RELAY NO.1 
CONTROL CIRCUIT FOR SHORT 

TO GROUND

 

z

Turn the ignition switch off.  

z

Inspect for continuity between 

main relay No.1 terminal A 
(wiring harness-side) and body 

ground.  

z

Is there continuity?  

Yes

Repair or replace suspected part, then go 
to Step 5.

No

Go to the next step.

4

INSPECT FOR CORRECT PCM 
OPERATION

 

z

Disconnect all the PCM 
connectors.  

z

Visually inspect for: 

{

Pushed out pins  

{

Corrosion  

z

Connect all the PCM connectors 

and verify that they seat correctly. 

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

Yes

Go to the next step.

No

The system is correctly. Go to the next 

step.

5

VERIFY TROUBLESHOOTING OF 
DTC P0685 HAS BEEN 

COMPLETED

 

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:35 AM

Page 326 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

RaceChip Pro 2 Installation Manual preview
Pro 2
Brand: RaceChip Pages: 12
Mazda 1989 323 Manual preview
1989 323
Brand: Mazda Pages: 13
Prorack K544 Fitting Instructions Manual preview
K544
Brand: Prorack Pages: 20
GMC 2013 GMC Savana Owner'S Manual preview
2013 GMC Savana
Brand: GMC Pages: 398
Oldsmobile 2003 Alero Owner'S Manual preview
2003 Alero
Brand: Oldsmobile Pages: 354
National Cycle Quantum Wash'n'Wipe N30208 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30208
Brand: National Cycle Pages: 12
Mopar 77072498AB Manual preview
77072498AB
Brand: Mopar Pages: 18
Scosche HUD580GC Manual preview
HUD580GC
Brand: Scosche Pages: 12
Scosche MAGICGRIP MGQDWD-CPO Instructions Manual preview
MAGICGRIP MGQDWD-CPO
Brand: Scosche Pages: 12
Gacell SLH 27C User Manual preview
SLH 27C
Brand: Gacell Pages: 25
Tesla Gen 3 Manual preview
Gen 3
Brand: Tesla Pages: 42
Kargo Master PRO-IV Assembly Instructions Manual preview
PRO-IV
Brand: Kargo Master Pages: 8
VER-MAC PCMS-1210 QS User Manual preview
PCMS-1210 QS
Brand: VER-MAC Pages: 44
Macally HRMOUNTPROTRAY User Manual preview
HRMOUNTPROTRAY
Brand: Macally Pages: 19
TAUBENREUTHER 2360-00 Manual preview
2360-00
Brand: TAUBENREUTHER Pages: 10
Chevrolet 2003 Monte Carlo Owner'S Manual preview
2003 Monte Carlo
Brand: Chevrolet Pages: 386
Chevrolet 2003 Impala Owner'S Manual preview
2003 Impala
Brand: Chevrolet Pages: 410
Oldsmobile 2003 Bravada Owner'S Manual preview
2003 Bravada
Brand: Oldsmobile Pages: 410

Brands by name

Popular brands

Load more brands