Mazda CX-9 Grand Touring 2007 Manual Download Page 320

Page: 320 / 1056

Fig. 41: Installing Quick Release Connector

Courtesy of MAZDA MOTORS CORP.

FUEL INJECTOR REMOVAL/INSTALLATION [MZI-3.5]

1. Complete the "BEFORE REPAIR PROCEDURE". (See

BEFORE REPAIR PROCEDURE [MZI-

3.5]

2. Disconnect the negative battery cable. (see

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

3. Remove the engine cover. (see

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

4. Remove the dynamic chamber (see

INTAKE-AIR SYSTEM REMOVAL/INSTALLATION [MZI-

3.5]

5. Remove in the order indicated in the table.

Fig. 42: Identifying Fuel Injector Components With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

6. Install in the reverse order of removal.

WARNING:

Fuel is very flammable liquid. If fuel spills or leaks from the

pressurized fuel system, it will cause serious injury or death and
facility breakage. Fuel can also irritate skin and eyes. To prevent

this, always complete the "Fuel Line Safety Procedure", while
referring to the "BEFORE SERVICE PRECAUTION".

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Fuel System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:24:13 AM

Page 32

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands