Mazda CX-9 Grand Touring 2007 Manual Download Page 140 | Manualshive

Page: 140 / 1056

background image

1. Inspect the fuel hose and fuel pipe sealing surface for damage and deformation.

z

If there is any malfunction, replace it with a new one.

2. Apply a small amount of clean engine oil to the sealing surface of the fuel pipe.
3. Reconnect the fuel hose straight to the fuel pipe until a click is heard.

Fig. 38: Identifying Fuel Hose And Checker Tab

Courtesy of MAZDA MOTORS CORP.

4. Lightly pull and push the quick release connector a few times by hand, and then verify that it can move

2.0-3.0 mm {0.08-0.12 in} and is connected securely.

TYPE E INSTALLATION

1. Inspect the fuel hose and fuel pipe sealing surface for damage and deformation.

z

If there is any malfunction, replace it with a new one.

2. Install the quick release connector.

z

Insert the fuel pipe straight to the end of the quick release connector.

z

Push down the retainer using a finger.

If the retainer cannot be pushed down, push the fuel pipe further to the quick release
connector.

3. Lightly pull and push the quick release connector a few times by hand, and then verify that it is connected

securely.

z

A checker tab is integrated with the quick release connector for new fuel
hoses and evaporative hoses. Remove the checker tab from the quick

release connector after the connector is completely engaged with the fuel

pipe.

NOTE:

z

If the quick release connector does not move at all, disconnect it,
verify that the O-ring is not damaged or has not slipped, and then

reconnect the quick release connector.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Emission System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:24:50 AM

Page 25

© 2005 Mitchell Repair Information Company, LLC.

«
...
138
139
140
141
142
...
»

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Titanium Series

Brand: Fass Pages: 13

Brand: Kia Pages: 385

Cushman Turf Truckster

Brand: Jacobsen Pages: 210

Brand: Alpine Pages: 2

Brand: Whispbar Pages: 15

Camaro 12000 1968 Series

Brand: Chevrolet Pages: 455

Sterling ALL-TERRAIN 576

Brand: Roadmaster Pages: 12

Brand: Blue Ox Pages: 7

Brand: Shad Pages: 3

Gold Cruuse Cruisecontrol GC90

Brand: John Gold Pages: 24

Brand: Whispbar Pages: 14

Brand: AutoWatch Pages: 4

MagicWatch MWE250

Brand: Waeco Pages: 172

Brand: Ecco Pages: 9

Brand: Hudson Pages: 34

Brand: Radical Sportscars Pages: 44

Brand: KEKO Pages: 3

Brand: Movon Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands