manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

Turn the ignition switch off.  

z

Inspect for continuity between 
OCV (RH) terminal B (wiring 

harness-side) and body ground.  

z

Is there continuity?  

No

Go to the next step.

8

INSPECT PCM CONNECTOR FOR 
POOR CONNECTION

 

z

Disconnect the PCM connector.  

z

Inspect for poor connection (such 
as damaged/pulled-out pins, 

corrosion).  

z

Is there any malfunction?  

Yes

Repair or replace suspected part, then go to 
Step 10.

No

Go to the next step.

9

INSPECT OCV (RH) CIRCUIT FOR 
OPEN CIRCUIT

 

z

Turn the ignition switch off.  

z

Measure the resistance between 
the OCV (RH) connector terminal 

B (wiring harness-side) and PCM 
terminal 2BP (wiring harness-

side).  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 

the next step.

10

VERIFY TROUBLESHOOTING OF 
DTC P0010 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 

connectors reconnected.  

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Clear the DTC from the PCM 

memory using the M-MDS.  

z

Start the engine and run it at idle.  

z

Retrieve DTCs using the M-MDS. 

z

Is the PENDING CODE for this 
DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

11

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "AFTER REPAIR 

PROCEDURE". 

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:29 AM

Page 28 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

cam 2850 Mounting Instructions preview
2850
Brand: cam Pages: 2
Dapper Lighting 575 Install Manual preview
575
Brand: Dapper Lighting Pages: 2
Yakima K800 Instructions Manual preview
K800
Brand: Yakima Pages: 8
Whispbar K783W Fitting Instructions Manual preview
K783W
Brand: Whispbar Pages: 16
Mitsubishi 1998 FTO Technical Information Manual preview
1998 FTO
Brand: Mitsubishi Pages: 160
Cadillac 2004 CTS Owner'S Manual preview
2004 CTS
Brand: Cadillac Pages: 442
I.D. Systems Vehicle Asset Communicator User Manual preview
Vehicle Asset Communicator
Brand: I.D. Systems Pages: 41
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Brand: Ecco Pages: 24
rockymounts SplitRailLS Installation Instructions Manual preview
SplitRailLS
Brand: rockymounts Pages: 6
Thule 1809 Instruction Manual preview
1809
Brand: Thule Pages: 4
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Brand: Alphasonik Pages: 8
Horn Tools HJIMRR02FIT Mounting Instructions preview
HJIMRR02FIT
Brand: Horn Tools Pages: 12
Jeep CHEROKEE 2017 User Manual preview
CHEROKEE 2017
Brand: Jeep Pages: 374
Skoda FABIA II TMB PS 035 Mounting And User Instructions preview
FABIA II TMB PS 035
Brand: Skoda Pages: 16
Setma E12PE27000 Instruction Manual preview
E12PE27000
Brand: Setma Pages: 13
Masterbuilt Hitch-Haul 30110315 Operation Manual & Safety Instructions preview
Hitch-Haul 30110315
Brand: Masterbuilt Pages: 2
Mazda 2011 CX-9 Owner'S Manual preview
2011 CX-9
Brand: Mazda Pages: 605
CITROEN CX 2000 Repair Manual preview
CX 2000
Brand: CITROEN Pages: 394

Brands by name

Popular brands

Load more brands