manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P1464 [MZI-3.5] 

DTC P1464 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

z

Inspect the PCV valve heater 

control and PCV valve heater 

fitting. 

(see 

POSITIVE CRANKCASE 

VENTILATION (PCV) VALVE 

INSPECTION [MZI-3.5].

 ) 

(see 

POSITIVE CRANKCASE 

VENTILATION (PCV) VALVE 
HEATER FITTING 

INSPECTION [MZI-3.5].

 ) 

z

Is there any malfunction?  

No

Go to the next step.

9

VERIFY TROUBLESHOOTING OF 
DTC P145E HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 

connectors reconnected.  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Perform the "KOEO or KOER 

self-test" using the M-MDS. 

(See 

KOEO/KOER SELF TEST 

[MZI-3.5]

.) 

z

Is the PENDING CODE for the 
DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

10

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "AFTER REPAIR 

PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P1464

A/C demand out of self-test range

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:37 AM

Page 370 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

TATA Motors Safari Owner'S Manual & Service Book preview
Safari
Brand: TATA Motors Pages: 161
TAUBENREUTHER 16 - 590 Fitting Instructions Manual preview
16 - 590
Brand: TAUBENREUTHER Pages: 11
Yakima SKYBOX Series Manual preview
SKYBOX Series
Brand: Yakima Pages: 15
Metra Electronics 70-5511 Installation Instructions preview
70-5511
Brand: Metra Electronics Pages: 2
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Brand: Vauxhall Pages: 131
Paccar PACCHARGE AC20 Installation Manual preview
PACCHARGE AC20
Brand: Paccar Pages: 63
Oldsmobile 1995 Cutlass Supreme Owner'S Manual preview
1995 Cutlass Supreme
Brand: Oldsmobile Pages: 340
BrandMotion FLTW-7511 Installation Manual preview
FLTW-7511
Brand: BrandMotion Pages: 6
Saab 32000574 Installation Instructions Manual preview
32000574
Brand: Saab Pages: 9
Rydeen BSS2 Owner'S Manual preview
BSS2
Brand: Rydeen Pages: 14
Brodit ProClip 833995 Manual preview
ProClip 833995
Brand: Brodit Pages: 2
MMD 41240 Quick Manual preview
41240
Brand: MMD Pages: 3
Chevrolet Chevy II 1965 Owner'S Manual preview
Chevy II 1965
Brand: Chevrolet Pages: 46
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Brand: Subaru Pages: 399
AUTOTECH 10.297.300K-303K Installation Instructions preview
10.297.300K-303K
Brand: AUTOTECH Pages: 1
Metra Electronics 95-7322 Installation Instructions Manual preview
95-7322
Brand: Metra Electronics Pages: 16
Fortin Electronic Systems EVO-CAN Suggested Wiring Configuration preview
EVO-CAN
Brand: Fortin Electronic Systems Pages: 5
TRAMEC CV 1 Series Manual preview
CV 1 Series
Brand: TRAMEC Pages: 116

Brands by name

Popular brands

Load more brands