manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

 
Are all above items normal?

z

For No.4 cylinder: 2BH

  

z

For No.5 cylinder: 2BB

  

z

For No.6 cylinder: 2BD

  

No

Replace the fuel injector.

9

Is the air cleaner element free of 
clogging?

Yes

Go to the next step.

No

Replace the air cleaner element.

10

Perform the spark test. 

(See 

ENGINE CONTROL SYSTEM 

OPERATION INSPECTION [MZI-

3.5]

.) 

Is strong blue spark visible at each 

cylinder?

Yes

Go to the next step.

No

Repair or replace the malfunctioning 
part.

11

Install the fuel pressure gauge between 
the fuel filter and fuel distributor. 

Short check connector terminal F/P to 
body GND using a jumper wiring. 

Turn the ignition switch to the ON 

position (Engine off). 
Is the fuel line pressure correct with 

ignition switch at ON? 
(see 

FUEL LINE PRESSURE 

INSPECTION [MZI-3.5]

 .)

Yes

Go to the next step.

No

Zero or low:

  

Inspect the fuel pump relay and fuel 
pump circuit. 

Inspect the fuel line for clogging. 
If there is no malfunction, replace the 

fuel pump unit. 
(see 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION [MZI-
3.5]

 .) 

High:

  

Replace the fuel pump unit. 

(see 

FUEL PUMP UNIT 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

12

Inspect the following PIDs: 

z

ECT  

z

O2S11 (When engine can be 

started.)  

z

O2S12 (When engine can be 
started.)  

z

O2S21 (When engine can be 

started.)  

z

O2S22 (When engine can be 
started.)  

z

MAF 

(see 

PCM INSPECTION 

[MZI-3.5]

 .) 

Are PIDs normal? 

Yes

Go to the next step.

No

Repair or replace the malfunctioning 
part.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:27:38 AM

Page 92 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Kargo Master 40640 Assembly Manual preview
40640
Brand: Kargo Master Pages: 5
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Brand: Ultra-tow Pages: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Brand: Mercedes-Benz Pages: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Brand: Menabo Pages: 8
Camtree G-51 Instruction Manual preview
G-51
Brand: Camtree Pages: 5
Van Guard VG273 Fitting Instructions preview
VG273
Brand: Van Guard Pages: 3
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Brand: Dakota Digital Pages: 3
Kargo Master 8006A Instruction Manual preview
8006A
Brand: Kargo Master Pages: 19
Safe Fleet PRIME DESIGN VBR3-FT31B Manual preview
PRIME DESIGN VBR3-FT31B
Brand: Safe Fleet Pages: 12
Axxess AXRC-CH1 Installation Instructions Manual preview
AXRC-CH1
Brand: Axxess Pages: 8
Dodge Charger 1973 Body Service Manual preview
Charger 1973
Brand: Dodge Pages: 276
Saab 32 025 603 Installation Instructions Manual preview
32 025 603
Brand: Saab Pages: 15
Air Lift 88365 Installation Manual preview
88365
Brand: Air Lift Pages: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Brand: Dolphin Pages: 16
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Brand: Saturn Pages: 440
Mazda 2008 B2300 Truck Owner'S Manual preview
2008 B2300 Truck
Brand: Mazda Pages: 280
BMW 84 61 0 028 926 Installation Instructions Manual preview
84 61 0 028 926
Brand: BMW Pages: 13
Roadtrek SS Agile 2017 Owner'S Manual preview
SS Agile 2017
Brand: Roadtrek Pages: 61

Brands by name

Popular brands

Load more brands