Mazda CX-9 Grand Touring 2007 Manual Download Page 454

Page: 454 / 1056

Pressurize the fuel system. Refer

to the Workshop Fuel System for

the Fuel System Pressure Release
procedure to pressurize the fuel

system.

Compare the fuel pressure reading
to the Fuel System Specification

Chart.

Is the fuel pressure within range?

INSPECT FUEL PUMP GROUND
CIRCUIT FOR OPEN CIRCUIT IN

WIRING HARNESS

Disconnect the fuel pump
connector.

Measure the resistance between

fuel pump connector terminal D
(wiring harness-side) and body

ground.

Is the voltage less than 0.5 ohm?

NOTE:

Refer to the Wiring Diagrams
Manual for schematic and

connector information.

Yes

Go to the next step.

Repair or replace suspected part, Then go
to Step 11.

INSPECT FUEL PUMP POWER
SUPPLY CIRCUIT FOR OPEN

CIRCUIT IN WIRING HARNESS

Disconnect the fuel pump

connector.

Turn the ignition switch to the ON
position (Engine off).

Access the PCM and control the

FP PID.

Measure the voltage between fuel
pump connector terminal B

(wiring harness-side) and body
ground.

Is the voltage more than 10 V?

Yes

Go to the next step.

Repair or replace suspected part, Then go
to Step 11.

INSPECT FUEL PRESSURE LEAK

NOTE:

Yes

Perform the KOEO self-test. Go to Step
10.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:30 AM

Page 107

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands