Mazda CX-9 Grand Touring 2007 Manual Download Page 702

Page: 702 / 1056

DTC P1290 [MZI-3.5]

DTC P1290 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

{

CHT sensor terminal B

(wiring harness-side) and

PCM terminal 2AN (wiring
harness-side).

Are there continuity?

INSPECT CHT SENSOR

Inspect the CHT sensor.

(see

CYLINDER HEAD

TEMPERATURE (CHT)

SENSOR INSPECTION [MZI-
3.5].

)

Is there any malfunction?

Yes

Replace the CHT sensor, then go to the

next step.

Go to the next step.

VERIFY TROUBLESHOOTING OF
DTC P1289 HAS BEEN

COMPLETED

Verify that all disconnected
connectors reconnected.

Clear the DTC from the PCM

memory using the M-MDS.

Perform the KOEO or KOER self-

test using the M-MDS.

(See

KOEO/KOER SELF TEST

[MZI-3.5]

Is the PENDING CODE for the
DTC present?

Yes

Replace the PCM, then go to the next step.
(see

PCM

REMOVAL/INSTALLATION [MZI-
3.5]

Go to the next step.

VERIFY AFTER REPAIR

PROCEDURE

Perform "AFTER REPAIR
PROCEDURE".

(See

AFTER REPAIR

PROCEDURE [MZI-3.5]

Are any DTCs present?

Yes

Go to the applicable DTC inspection.

(See

DTC TABLE [MZI-3.5]

Troubleshooting completed.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:36 AM

Page 355

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands