Mazda CX-9 Grand Touring 2007 Manual Download Page 921

Page: 921 / 1056

INSPECTION [MZI-3.5]

If the PID reading is out of range, perform the following:

Remove the air duct from throttle valve body.

Verify that the throttle valve opens when throttle pedal is depressed.

If the throttle valve opens, inspect the throttle position sensor and related wiring
harness.

If the throttle valve does not open, inspect the throttle actuator control motor and

related wiring harness.

FUEL INJECTOR OPERATION INSPECTION

FUEL INJECTOR OPERATION CHART

FUEL CUT CONTROL SYSTEM INSPECTION

If simulation function of the M-MDS is used:

STEP INSPECTION

RESULTS ACTION

While cranking the engine, inspect for

fuel injector operation sound at each
cylinder using a soundscope.

Is operation sound heard?

Yes

Fuel injector operation is normal.

All cylinders not heard:

Go to the next step.

Some cylinders not heard:

Go to Step 3.

Perform main relay operation

inspection.
Is main relay operation normal?

Yes

Inspect the following:

Fuel injector power system

related wiring harness and
connectors

PCM connectors

Fuel injector GND and related
wiring harness and connectors

Repair or replace malfunctioning

parts.

Switch fuel injector connector of not
operating fuel injector with operating

fuel injector.
Is operation sound heard?

Yes

Go to the next step.

Replace the fuel injector.

Are wiring harness and connectors of
not operation fuel injector normal?

(Open or short)

Yes

Inspect PCM terminal voltage of fuel
injector signal.

Repair or replace malfunctioning

parts.

NOTE:

This inspection has to perform after the Fuel Injector Operation Inspection.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:38 AM

Page 104

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands