manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

5

INSPECT PCV VALVE HEATER 
CONTROL AND PCV VALVE 

HEATER FITTING CIRCUIT FOR 
SHORT TO GROUND

 

z

Turn the ignition switch off.  

z

Inspect for continuity between the 
following circuit: 

{

PCV valve heater control 

terminal B (wiring harness-
side) and body ground  

{

PCV valve heater fitting 

terminal B (wiring harness-
side) and body ground  

z

Are there continuity?  

Yes

Repair or replace suspected part, then go to 
Step 9.

No

Go to the next step.

6

INSPECT PCM CONNECTOR FOR 
POOR CONNECTION

 

z

Turn the ignition switch off.  

z

Disconnect PCM connector.  

z

Inspect for poor connection (such 

as damaged/pulled-out pins, 

corrosion).  

z

Are there any malfunction?  

Yes

Repair or replace suspected part, then go to 
Step 9.

No

Go to the next step

7

INSPECT PCV VALVE HEATER 
CONTROL AND PCV VALVE 

HEATER FITTING FOR OPEN 
CIRCUIT

 

z

Inspect for continuity between the 

following circuit: 

{

PCV valve heater control 

terminal B (wiring harness-
side) and PCM terminal 

2BL (wiring harness-side)  

{

PCV valve heater fitting B 
(wiring harness-side) and 

PCM terminal 2AU (wiring 
harness-side)  

z

Are there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 
Step 9.

8

INSPECT PCV VALVE HEATER 

CONTROL AND PCV VALVE 
HEATER FITTING

 

Yes

Replace the malfunctioning part, then go 

to the next step.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:37 AM

Page 369 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Brand: Bimmer Jakes Pages: 4
Victory 4x4 UNI-UPRS Install Instructions Manual preview
UNI-UPRS
Brand: Victory 4x4 Pages: 13
Axxess AX-LR904 Installation Instructions Manual preview
AX-LR904
Brand: Axxess Pages: 8
SeaSucker SX6150 Quick Start Manual preview
SX6150
Brand: SeaSucker Pages: 9
Sirius Satellite Radio Streamer GTR Installation Manual preview
Streamer GTR
Brand: Sirius Satellite Radio Pages: 8
Toyota AURION 2013 Owner'S Manual preview
AURION 2013
Brand: Toyota Pages: 371
GMC Chevrolet Silverado 2500HD 2021 Owner'S Manual preview
Chevrolet Silverado 2500HD 2021
Brand: GMC Pages: 433
Safe Fleet PRIME DESIGN VRR-NV200 Manual preview
PRIME DESIGN VRR-NV200
Brand: Safe Fleet Pages: 12
Volvo 1996 960 Quick Tips preview
1996 960
Brand: Volvo Pages: 10
Mobility Networks RPH 35.13 Use And Maintenance Manual preview
RPH 35.13
Brand: Mobility Networks Pages: 52
iArmor EDGE IA-W208 Manual preview
EDGE IA-W208
Brand: iArmor Pages: 6
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
Needit Park Mini User Manual preview
Park Mini
Brand: Needit Pages: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Brand: Gemini Pages: 6
Enduro EM203 User Manual preview
EM203
Brand: Enduro Pages: 52
ORA XL MIRROR Installation Instructions Manual preview
XL MIRROR
Brand: ORA Pages: 7
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Brand: Brodit Pages: 2
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Brand: Reliant Pages: 206

Brands by name

Popular brands

Load more brands