Mazda CX-9 Grand Touring 2007 Manual Download Page 557

Page: 557 / 1056

DTC P0420, P0430 [MZI-3.5]

C (wiring harness-side) and
PCM terminal 2AA (wiring

harness-side)

{

Ignition coil No.6 terminal

C (wiring harness-side) and
PCM terminal 2AE (wiring

harness-side)

Are there continuity?

INSPECT IGNITION COIL

Inspect ignition coil.

(see

IGNITION COIL

INSPECTION [MZI-3.5]

Are there ignition coil normal?

Yes

Go to the next step.

Replace the ignition coil, then go to the
next step.

VERIFY TROUBLESHOOTING OF

DTC P0351, P0352, P0353, P0354,
P0355 and P0356 COMPLETED

Verify that all disconnected

connectors reconnected.

Clear the DTC from the PCM

memory using the M-MDS.

Perform the "KOEO or KOER
self-test" using the M-MDS.

(See

KOEO/KOER SELF TEST

[MZI-3.5]

Is the PENDING CODE for the

DTC present?

Yes

Replace the PCM, then go to the next step.

(see

PCM

REMOVAL/INSTALLATION [MZI-

3.5]

Go to the next step.

VERIFY AFTER REPAIR
PROCEDURE

Perform "AFTER REPAIR

PROCEDURE".

(See

AFTER REPAIR

PROCEDURE [MZI-3.5]

Are any DTCs present?

Yes

Go to the applicable DTC inspection.
(See

DTC TABLE [MZI-3.5]

Troubleshooting completed.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:32 AM

Page 210

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands