manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

1. Push the rear oil seal slightly in by hand.  
2. Tap the rear oil seal in evenly using the 

SST

 and a hammer. 

Substitution SST

  

z

49 W011 101

 

Outer diameter: 105 mm {4.13 in} or more Inner diameter: 93-105 mm {3.7-4.1 in} Tube with 

board thickness 2 mm {0.079 in} or more 

Fig. 105: Tapping In Rear Oil Seal Using SST

 

Courtesy of MAZDA MOTORS CORP.

 

ENGINE REMOVAL/INSTALLATION [MZI-3.5] 

1. Perform "Fuel Line Safety Procedures". Leave the fuel pump relay removed. (see 

BEFORE REPAIR 

PROCEDURE [MZI-3.5]

 .)  

2. Disconnect both battery cables.  
3. Remove the battery and battery tray. (see 

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

 .)  

4. Drain the power steering fluid. (see 

POWER STEERING FLUID INSPECTION

 .)  

5. Drain the engine coolant. (see 

ENGINE COOLANT REPLACEMENT [MZI-3.5]

 .)  

6. Remove the engine cover. (See 

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

.)  

7. Remove the ventilation hose. (see 

QUICK RELEASE CONNECTOR (EMISSION SYSTEM) 

REMOVAL/INSTALLATION [MZI-3.5].

) 

NOTE:

z

Lubricate the rear oil seal lips and bore with clean engine oil. 

WARNING:

z

Fuel vapor is hazardous. It can very easily ignite, causing serious 
injury and damage. Always keep sparks and flames away from fuel.  

z

Fuel line spills and leakage are dangerous. Fuel can ignite and cause 

serious injuries or death and damage. Fuel can also irritate skin and 
eyes. To prevent this, always complete the "Fuel Line Safety 

Procedure". (see BEFORE REPAIR PROCEDURE [MZI-3.5] .)  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE Mechanical (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:19:28 AM

Page 66 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Brand: Jeep Pages: 673
Paxton Automotive Novi Owner'S Installation Manual preview
Novi
Brand: Paxton Automotive Pages: 85
Thule 1489 Instructions Manual preview
1489
Brand: Thule Pages: 8
Mercedes-Benz GUARD S 500 Supplement To Operators Manual preview
GUARD S 500
Brand: Mercedes-Benz Pages: 30
Cadillac 2004 ESCALADE Customer Convenience/Personalization Manual preview
2004 ESCALADE
Brand: Cadillac Pages: 20
Saab 32000574 Installation Instructions Manual preview
32000574
Brand: Saab Pages: 9
Pet Gear TL9000 Instruction Manual preview
TL9000
Brand: Pet Gear Pages: 4
Suzuki IGNIS 2022 Series Manual preview
IGNIS 2022 Series
Brand: Suzuki Pages: 570
RAM 1500 CLASSIC 2020 Owner'S Manual preview
1500 CLASSIC 2020
Brand: RAM Pages: 360
Chrysler Dodge Caravan 2002 Manual preview
Dodge Caravan 2002
Brand: Chrysler Pages: 2399
Ednet 84104 User Manual preview
84104
Brand: Ednet Pages: 6
Mercedes-Benz 2013 S-CLASS Owner'S Manual preview
2013 S-CLASS
Brand: Mercedes-Benz Pages: 493
Altius ATHUDW-SCA User Manual preview
ATHUDW-SCA
Brand: Altius Pages: 16
Tuff Tonneaus Bunji Ute Installation Instructions preview
Bunji Ute
Brand: Tuff Tonneaus Pages: 4
BMW 530 GRAN TURISMO - 2010 Brochure preview
530 GRAN TURISMO - 2010
Brand: BMW Pages: 26
Whispbar K509 Fitting Instructions Manual preview
K509
Brand: Whispbar Pages: 34
Volkswagen 2013 GTI Brochure & Specs preview
2013 GTI
Brand: Volkswagen Pages: 11
Valeo 632201 Instruction Manual preview
632201
Brand: Valeo Pages: 76

Brands by name

Popular brands

Load more brands