Mazda CX-9 Grand Touring 2007 Manual Download Page 305

Page: 305 / 1056

Fig. 20: Exploded View Of Fuel Tank Components With Torque Specifications

Courtesy of MAZDA MOTORS CORP.

Fuel-filler pipe protector removal note

1. Remove the rear tire (LH).
2. Remove the splash shield (LH).
3. Remove the fuel-filler pipe protector.

Fuel-filler pipe removal note

1. Remove the rear tire (RH).

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Fuel System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:24:12 AM

Page 17

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands