manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

VOLTAGE INSPECTION 

1. Verify that no DTC related to APP sensor has been detected. 

z

If any DTCs related to APP sensor have been detected, perform the DTC inspection. (see 

DTC 

TABLE [MZI-3.5]

 .)  

2. Connect the M-MDS to the DLC-2.  
3. Turn the ignition switch to the ON position.  
4. Select TP1 or TP2 PID (voltage) on the M-MDS. 

Fig. 12: Identifying DLC-2 Connector

 

Courtesy of MAZDA MOTORS CORP.

 

5. Operate the accelerator pedal and verify that the TP1 or TP2 PID (voltage) changes as shown in the 

following graph. 

z

If not verified, perform the "Circuit Open/Short Inspection". 

„

If there is no open or short circuit, replace the throttle body. (see 

INTAKE-AIR SYSTEM 

REMOVAL/INSTALLATION [MZI-3.5]

 .)  

Fig. 13: Throttle Output Voltage Graph

NOTE:

z

Before performing the following inspection, make sure to follow the 
procedure as indicated in the troubleshooting flowchart. (see HOW TO 

USE THIS MANUAL .)  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:25:31 AM

Page 15 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Brand: Gardigo Pages: 36
Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
Quadratec QR3 Installation Manual preview
QR3
Brand: Quadratec Pages: 8
JANE be cool boosty Manual preview
be cool boosty
Brand: JANE Pages: 21
Gator GX5HDKT User Manual preview
GX5HDKT
Brand: Gator Pages: 8
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Brand: Waeco Pages: 172
Cadillac 1999 DeVille Owner'S Manual preview
1999 DeVille
Brand: Cadillac Pages: 368
Luverne 205760 Installation Instructions preview
205760
Brand: Luverne Pages: 3
Navman B2+ User Manual preview
B2+
Brand: Navman Pages: 27
Sears 580.32601 Owner'S Manual preview
580.32601
Brand: Sears Pages: 41
VER-MAC PCMS Series Operation, Safety And Maintenance Manual preview
PCMS Series
Brand: VER-MAC Pages: 64
Velleman CARS4500 User Manual preview
CARS4500
Brand: Velleman Pages: 12
Car-Systems Parktronic system Volkswagen Golf MK7 Assembly Manual preview
Parktronic system Volkswagen Golf MK7
Brand: Car-Systems Pages: 10
RHOX LGT-381L Installation Instructions Manual preview
LGT-381L
Brand: RHOX Pages: 8
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Brand: Carcomm Pages: 2
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Brand: RAM Pages: 330
Kuda-Phonebase 284380 Installation Instruction preview
284380
Brand: Kuda-Phonebase Pages: 3
Ford transit connect 2012 User Manual preview
transit connect 2012
Brand: Ford Pages: 299

Brands by name

Popular brands

Load more brands