Mazda CX-9 Grand Touring 2007 Manual Download Page 875

Page: 875 / 1056

NO.13 KNOCKING/PINGING-ACCELERATION/CRUISE [MZI-3.5]

DESCRIPTION AND POSSIBLE CAUSES

Is the engine compression correct?

Yes

Inspect the following:

Valve timing

Internal transaxle components

Brake system for dragging

Inspect for cause.

Verify test results.

{

If normal, return to diagnostic index to service any additional symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

{

If malfunction remains, inspect related Service Bulletins and/or On-line Repair
Information and perform repair or diagnosis.

If vehicle is repaired, troubleshooting completed.

If vehicle is not repaired or additional diagnostic information is not

available, replace the PCM.

(see

PCM REMOVAL/INSTALLATION [MZI-3.5]

KNOCKING/PINGING - ACCELERATION/CRUISE

DESCRIPTION

Sound is heard when air/fuel mixture is ignited by something other than spark plug
(such as hot spot in combustion chamber).

POSSIBLE CAUSE

Engine overheating due to cooling system malfunction

CHT sensor malfunction

IAT sensor malfunction

MAF sensor malfunction

Knock sensor malfunction

Erratic signal from CMP sensor

Inadequate engine compression

Inadequate fuel pressure

WARNING:

The following troubleshooting flow chart contains the fuel system diagnosis

and repair procedures. Read the following warnings before servicing the fuel
system:

Fuel vapor is hazardous. It can easily ignite, causing serious injury and
damage. Always keep sparks and flames away from fuel.

Fuel line spills and leakage are dangerous. Fuel can ignite and cause

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 58

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands