manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P0454 [MZI-3.5] 

DTC P0454 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

DIAGNOSTIC PROCEDURE 

DTC P0454 (MZI-3.5) DIAGNOSTIC PROCEDURE

 

z

Make sure to reconnect all 

disconnected connectors.  

z

Turn ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Start the engine and warm it up 

completely.  

z

Is same DTC present?  

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

10

VERIFY AFTER REPAIR 
PROCEDURE

 

z

Perform the "After Repair 
Procedure". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTCs present?  

Yes

Go to the applicable DTC inspection. 
(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P0454

Fuel tank pressure sensor intermittent

DETECTION 
CONDITION

 

z

The fuel tank pressure changes more than 14 inches of water in 0.10 s.  

POSSIBLE CAUSE

 

z

Intermittent open or short in the fuel tank pressure sensor or the fuel tank 
pressure sensor signal  

z

Fuel tank pressure sensor malfunction  

STEP

INSPECTION

ACTION

1

VERIFY FREEZE FRAME DATA 
HAS BEEN RECORDED

 

z

Has FREEZE FRAME DATA 
been recorded?  

Yes

Go to the next step.

No

Record FREEZE FRAME DATA on the 
repair order, then go to the next step.

2

VERIFY RELATED REPAIR 

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

Yes

Perform repair or diagnosis according to 

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:33 AM

Page 236 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

UltraGauge EM Installation & Operation Manual preview
EM
Brand: UltraGauge Pages: 55
Chevrolet 2013 Spark Owner'S Manual preview
2013 Spark
Brand: Chevrolet Pages: 356
Ford Zephyr 2007 Owner'S Manual preview
Zephyr 2007
Brand: Ford Pages: 272
Pontiac 2004 Sunfire Owner'S Manual preview
2004 Sunfire
Brand: Pontiac Pages: 376
Jeep COMPASS 2018 Owner'S Manual preview
COMPASS 2018
Brand: Jeep Pages: 712
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Brand: Buick Pages: 428
Trailboss HD86 Fitting Instructions preview
HD86
Brand: Trailboss Pages: 5
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Brand: Saab Pages: 12
travall TDG-1301 Fitting Instruction preview
TDG-1301
Brand: travall Pages: 2
Gacell 13553 User Manual preview
13553
Brand: Gacell Pages: 12
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Brand: GMC Pages: 430
Quadratec 16053.5300 Installation Manual preview
16053.5300
Brand: Quadratec Pages: 6
Volvo S90 2018 Quick Manual preview
S90 2018
Brand: Volvo Pages: 42
FVC Sprinter Side Ladder Installation Manual preview
Sprinter Side Ladder
Brand: FVC Pages: 8
Mazda 2010 MX-5 Miata Specification preview
2010 MX-5 Miata
Brand: Mazda Pages: 8
Toyota RAV-4 2015 Series Owner'S Manual Supplement preview
RAV-4 2015 Series
Brand: Toyota Pages: 50
DEFA MultiCharger 1204 User'S Installation Manual preview
MultiCharger 1204
Brand: DEFA Pages: 28
Steelmate PTS800V7 User Manual preview
PTS800V7
Brand: Steelmate Pages: 14

Brands by name

Popular brands

Load more brands