manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

Has FREEZE FRAME DATA been 

recorded?  

repair order, then go to the next step.

2

VERIFY RELATED REPAIR 

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 
and/or on-line repair information 

availability.  

z

Is any related Service Bulletins 
available?  

Yes

Perform repair or diagnosis according to 

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 
the next step.  

No

Go to the next step.

3

INSPECT ALL OTHER PATS DTCs

 

z

Repair all other PATS DTCs before 
P1260. 

(see 

IMMOBILIZER SYSTEM 

COMPONENT 

REPLACEMENT/KEY 
ADDITION AND CLEARING 

[ADVANCED KEYLESS 
SYSTEM]

 .) 

(see 

IMMOBILIZER SYSTEM 

COMPONENT 
REPLACEMENT/KEY 

ADDITION AND CLEARING 

[KEYLESS ENTRY SYSTEM]

 .) 

z

Have all other PATS DTCs been 
diagnosed?  

Yes

Go to the next step.

No

(see 

IMMOBILIZER SYSTEM 

COMPONENT REPLACEMENT/KEY 

ADDITION AND CLEARING 
[ADVANCED KEYLESS SYSTEM]

 .) 

(see 

IMMOBILIZER SYSTEM 

COMPONENT REPLACEMENT/KEY 

ADDITION AND CLEARING 
[KEYLESS ENTRY SYSTEM]

 .)

4

INSPECT FOR OTHER 

POWERTRAIN DTCs

 

z

Repair all other powertrain DTCs 

before P1260.  

z

Have all other powertrain DTCs 
been diagnosed?  

Yes

Go to the next step.

No

Go to the appropriate DTC 

troubleshooting.

5

ATTEMPT TO START ENGINE

 

z

Complete the keep alive memory.  

z

Reset to clear DTC 1260.  

z

This reset initializes the PCM to 
communicate with the PATS.  

z

Attempt to start the engine.  

Yes

No system malfunctions exists at this 

time. 
For intermittent No Starts or Start Stalls, 

verify intermittent PATS faults. 
Then go to the next step. 

NOTE:

z

PATS cannot stall the engine after 

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:36 AM

Page 346 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

GMC SIERRA 2002 Manual preview
SIERRA 2002
Brand: GMC Pages: 499
Kia Amanti Owner'S Manual preview
Amanti
Brand: Kia Pages: 290
Dometic PERFECTVIEW CAM80AHD Installation And Operating Manual preview
PERFECTVIEW CAM80AHD
Brand: Dometic Pages: 196
MAXWORKS 70275 Instruction Manual & Parts Catalogue preview
70275
Brand: MAXWORKS Pages: 7
SAN HIMA SH-TENT-SY20 User Manual preview
SH-TENT-SY20
Brand: SAN HIMA Pages: 7
Paccar Peterbilt SmartAir Operator'S Manual preview
Peterbilt SmartAir
Brand: Paccar Pages: 58
Mercedes-Benz 300 SL Operator'S Manual preview
300 SL
Brand: Mercedes-Benz Pages: 153
Safe Fleet inView 360 Fusion Calibration Manual preview
inView 360 Fusion
Brand: Safe Fleet Pages: 27
Seat ROADSIDE ASSISTANCE Handbook preview
ROADSIDE ASSISTANCE
Brand: Seat Pages: 44
Hella AREIA 7040 Installation Instructions Manual preview
AREIA 7040
Brand: Hella Pages: 21
Qeedon Higlow Series Product Instruction preview
Higlow Series
Brand: Qeedon Pages: 2
SAFARI SS18HF Manual preview
SS18HF
Brand: SAFARI Pages: 5
Yakima Landing Pad 11 Manual preview
Landing Pad 11
Brand: Yakima Pages: 28
IOGear GBHFK201W6 User Manual preview
GBHFK201W6
Brand: IOGear Pages: 38
Whispbar K723W Fitting Instructions Manual preview
K723W
Brand: Whispbar Pages: 77
iSimple IS7705 Installation & Operation Manual preview
IS7705
Brand: iSimple Pages: 8
MiX Telematics FM 3617i Installation Manual preview
FM 3617i
Brand: MiX Telematics Pages: 39
Blue Ox BX2323 Installation Instructions Manual preview
BX2323
Brand: Blue Ox Pages: 9

Brands by name

Popular brands

Load more brands