Mazda CX-9 Grand Touring 2007 Manual Download Page 179

Page: 179 / 1056

1. Disconnect the PCM connector. (See

PCM REMOVAL/INSTALLATION [MZI-3.5]

2. Inspect the following wiring harnesses for open or short. (Continuity inspection)

Open circuit

If there is no continuity, the circuit is open. Repair or replace the wiring harness.

{

KS terminal A and PCM terminal 2Q

{

KS terminal B and PCM terminal 2M

{

KS terminal C and PCM terminal 2L

{

KS terminal D and PCM terminal 2G

Short circuit

If there is continuity, the circuit is shorted. Repair or replace the wiring harness.

{

KS terminal A and power supply

{

KS terminal A and body ground

{

KS terminal B and power supply

{

KS terminal B and body ground

{

KS terminal C and power supply

{

KS terminal C and body ground

{

KS terminal D and power supply

{

KS terminal D and body ground

CYLINDER HEAD TEMPERATURE (CHT) SENSOR

REMOVAL/INSTALLATION [MZI-3.5]

1. Disconnect the negative battery cable.
2. Remove the following part for easier access.

Perform the following procedure to remove the intake manifold.

1. Remove the ventilation hose. (see

QUICK RELEASE CONNECTOR (EMISSION SYSTEM)

REMOVAL/INSTALLATION [MZI-3.5].

)

2. Remove the vacuum hose (to purge solenoid valve). (see

QUICK RELEASE CONNECTOR

(EMISSION SYSTEM) REMOVAL/INSTALLATION [MZI-3.5].

)

3. Remove the fuel hose. (see

QUICK RELEASE CONNECTOR (FUEL SYSTEM)

REMOVAL/INSTALLATION [MZI-3.5].

)

4. Remove the fuel distributor. (see

FUEL INJECTOR REMOVAL/INSTALLATION [MZI-

3.5]

NOTE:

Do not reuse the CHT sensor, install a new sensor.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Control System (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:25:31 AM

Page 38

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands