Mazda CX-9 Grand Touring 2007 Manual Download Page 213

Page: 213 / 1056

Fig. 24: Removing Hole Seal

Courtesy of MAZDA MOTORS CORP.

ENGINE FRONT COVER AND NO.3 ENGINE MOUNT BRACKET REMOVAL NOTE

1. Loosen the engine front cover and No.3 engine mount bracket installation bolts in the order shown in the

figure.

Fig. 25: Identifying Engine Front Cover And No. 3 Engine Mount Bolt Removal Sequence

Courtesy of MAZDA MOTORS CORP.

2. Install 4 of the engine front cover bolts (finger tightened) into the 4 threaded holes in the engine front

cover.

1. Tighten the bolts one turn at a time in a crisscross pattern until the engine front cover-to-cylinder

block seal is released.

2. Remove the engine front cover.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 22

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands