manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

z

Has FREEZE FRAME DATA 

been recorded?  

No

Record FREEZE FRAME DATA on the 
repair order, then go to the next step.

2

VERIFY RELATED REPAIR 

INFORMATION AVAILABILITY

 

z

Verify related Service Bulletins 

and/or on-line repair information 
availability.  

z

Is any related Service Bulletins 

available?  

Yes

Perform repair or diagnosis according to 

the available Service Bulletins. 

z

If the vehicle is not repaired, go to 

the next step.  

No

Go to the next step.

3

INSPECT DRIVE BELT 
CONDITION

 

z

Verify that drive belt auto 
tensioner indicator mark does not 

exceed limit.  

z

Is drive belt normal?  

Yes

Go to the next step.

No

Replace and/or adjust drive belt, then go to 
Step 12. 

(see 

DRIVE BELT INSPECTION 

[MZI-3.5]

 .)

4

INSPECT GENERATOR 
TERMINAL FOR POOR 

INSTALLATION

 

z

Turn the engine switch off.  

z

Inspect generator terminal B for 

looseness.  

z

Are there any malfunction?  

Yes

Connect generator terminal B correctly, 
then go to Step 12.

No

Go to the next step.

5

INSPECT GENERATOR CIRCUIT 
FOR SHORT TO POWER SUPPLY

 

z

Turn the ignition switch to the ON 
position (Engine off).  

z

Measure voltage between 

generator terminal LI (wiring 
harness-side) and body ground.  

z

Is voltage 

B+?

  

Yes

Repair or replace suspected part, then go to 
Step 12.

No

Go to the next step.

6

INSPECT GENERATOR CIRCUIT 

FOR SHORT TO GROUND

 

z

Inspect for continuity between 

generator terminal LI (wiring 
harness-side) and body ground.  

z

Is there continuity?  

Yes

Repair or replace suspected part, then go to 

the next step.

No

Go to the next step.

7

INSPECT PCM CONNECTOR FOR 

POOR CONNECTION

 

Yes

Repair or replace suspected part, then go to 

Step 12.

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:35 AM

Page 302 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Jeep Wrangler2018 Owner'S Manual preview
Wrangler2018
Brand: Jeep Pages: 608
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Brand: Quadratec Pages: 20
GMC 2005 Sierra Denali Owner'S Manual preview
2005 Sierra Denali
Brand: GMC Pages: 428
Mercedes-Benz GLA 250 2019 Operator'S Manual preview
GLA 250 2019
Brand: Mercedes-Benz Pages: 346
Thule Kit 1514 Instructions preview
Kit 1514
Brand: Thule Pages: 4
Car-Interface CI-RL4-ELINK Manual preview
CI-RL4-ELINK
Brand: Car-Interface Pages: 23
RuggON VD04 Quick Start Manual preview
VD04
Brand: RuggON Pages: 2
Haibang HA998 Series Installation Instructions Manual preview
HA998 Series
Brand: Haibang Pages: 6
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Brand: Actia Pages: 37
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Brand: Scosche Pages: 16
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Brand: Saab Pages: 12
Baja Designs 447575 Instructions preview
447575
Brand: Baja Designs Pages: 5
Ecco EC4210B-K Installation And Operation Instructions Manual preview
EC4210B-K
Brand: Ecco Pages: 9
EUFAB 16465 Operating Instructions Manual preview
16465
Brand: EUFAB Pages: 12
Camoplast T4S Installation Manuallines preview
T4S
Brand: Camoplast Pages: 19
JBL smartbase Quick Start Manual preview
smartbase
Brand: JBL Pages: 12
A-Tach Mounts 50232 Instructions preview
50232
Brand: A-Tach Mounts Pages: 2
Audi Audi 80 1987 Workshop Manual preview
Audi 80 1987
Brand: Audi Pages: 63

Brands by name

Popular brands

Load more brands