Mazda CX-9 Grand Touring 2007 Manual Download Page 247

Page: 247 / 1056

Fig. 85: Identifying Front Cooler Pipe And Bolt

Courtesy of MAZDA MOTORS CORP.

5. Install the

SST

using the following procedure.

Fig. 86: Identifying SST

Courtesy of MAZDA MOTORS CORP.

1. Install the right rear shaft of the

SST

to the bolt of the right shock absorber shown in the figure.

2. Install the left rear shaft of the

SST

to the bolt of the left shock absorber (Identical position to the

right side).

CAUTION:

Refer to the SST instruction manual for the basic handing
procedure.

NOTE:

When installing the SST, adjust the position of each shaft so that

they do not interfere with the vehicle body.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 56

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands