Mazda CX-9 Grand Touring 2007 Manual Download Page 55

Page: 55 / 1056

SOLENOIDS & SOLENOID VALVES

SOLENOIDS & SOLENOID VALVES LOCATION

SWITCHES

SWITCHES LOCATION

Passenger-Side Side Air Bag Sensor No.1

Near base of right "B" pillar.

Passenger-Side Side Air Bag Sensor No. 2

Near base of right "C" pillar.

PLG Touch Sensor (Left/Right)

At respective side of tailgate.

Rain Sensor

Forward of interior rearview mirror.

Rear Evaporator Temperature Sensor

Under center console.

Seat Recline Position Sensor

In driver's seat back.

Seat Slide Position Sensor

Under driver's seat.

Seat Track Position Sensor

Under driver's seat.

Seat Weight Sensor (Left/Right)

Under respective side of front passenger's seat.

Solar Radiation Sensor

Top left side of dash.

Steering Angle Sensor

In steering column.

Tilt Position Sensor (Front)

Under driver's seat.

Tilt Position Sensor (Rear)

Under driver's seat.

Washer Fluid-Level Sensor

In washer fluid reservoir.

Component

Location

AWD Solenoid

Near rear differential.

Canister Vent Solenoid Valve

Under left side of vehicle, forward of fuel tank.

Fuel Injectors No. 1, 2, & 3

On right cylinder bank.

Fuel Injectors No. 4, 5 & 6

On left cylinder bank.

Magnetic Clutch

Left front of engine.

Oil Control Valve (Left)

Front of left cylinder bank.

Oil Control Valve (Right)

Front of right cylinder bank.

Purge Solenoid Valve

Rear of engine compartment.

Steering Lock Unit

In steering column.

Component

Location

Brake Switch No. 1

On brake pedal assembly.

Brake Switch No. 2

On brake pedal assembly.

Buckle Switch (Driver/Passenger Side)

Integral to respective seat belt buckle assembly.

Door Lock-Link Switch (Left/Right Front)

In respective front door.

Door Lock-Link Switch (Left/Right Rear)

In respective rear door.

Door Switch (Left/Right Front)

At respective "B" pillar.

Door Switch (Left/Right Rear)

At respective "C" pillar.

Hood Latch Switch

Center front of engine compartment.

2007 Mazda CX-9 Grand Touring

2007 MAZDA CX-9

Microsoft

Sunday, November 15, 2009 9:30:18 AM

Page 4

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands