Mazda CX-9 Grand Touring 2007 Manual Download Page 897

Page: 897 / 1056

DIAGNOSTIC PROCEDURE

STEP INSPECTION

RESULTS ACTION

Connect the M-MDS to the DLC-2.
Turn the ignition switch to the ON

position (Engine off).
Retrieve any DTCs.

Are there any DTCs displayed?

Yes

DTC is displayed:

Go to the appropriate DTC inspection.

(see

DTC TABLE [MZI-3.5]

No DTC is displayed:

Go to the next step.

Disconnect A/C compressor connector.

Start engine and turn A/C switch on.

Is there correct voltage at A/C
compressor magnetic clutch terminal?

Specification

10.5 V or more

Yes

Inspect for GND condition of

magnetic clutch on A/C compressor.

If GND condition is normal, inspect
for open circuit magnetic clutch coil.

Go to the next step.

Disconnect refrigerant pressure switch

connector.
Connect jumper wiring between A/C

high pressure switch terminal.
Connect jumper wiring between

refrigerant pressure switch terminal.
Turn the ignition switch to the ON

position.
Turn A/C switch on and set blower fan

to any speed.
Does A/C work?

Yes

Inspect refrigerant pressure switch

operation.
If switch is normal, go to the next step.

Inspect for the following:

A/C switch is stuck open.

Open circuit in wiring harness
between refrigerant pressure

switch and PCM terminal 1R

Open circuit in wiring harness
between blower motor fan

switch and resistor (if blower
motor does not operate)

Evaporator temperature sensor

and A/C amplifier

Remove jumper wiring from the switch

connector.
Reconnect connector to refrigerant

pressure switch.
Start the engine and turn the A/C switch

on.
Does the fan operate?

Yes

Inspect whether A/C relay is stuck

open.
Replace if necessary.

Inspect the following and repair or

replace if necessary:

Refrigerant charging amount

A/C compressor for seizure

Verify test results.

{

If normal, return to diagnostic index to service any additional symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

{

If malfunction remains, inspect related Service Bulletins and/or On-line Repair

Information and perform repair or diagnosis.

If vehicle is repaired, troubleshooting completed.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:38 AM

Page 80

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands