manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

DTC P0506 [MZI-3.5] 

DTC P0506 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

 

INSPECTION [MZI-3.5]

 .) 

z

Is the engine compression normal? 

8

INSPECT FOR RESTRICTION IN 

EXHAUST SYSTEM AND TWC

 

z

Is there any restriction?  

Yes

Replace malfunctioning part, then go to 

the next step.

No

Go to the next step.

9

VERIFY TROUBLESHOOTING OF 

DTC P0505 HAS BEEN 
COMPLETED

 

z

Verify that all disconnected 
connectors are reconnected.  

z

Turn the ignition switch to the ON 

position (Engine off).  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Perform the KOEO and KOER 

self-test.  

z

Retrieve the DTCs using the M-
MDS.  

z

Is the PENDING CODE for this 

DTC present?  

Yes

Replace the PCM, then go to the next step.

(see 

PCM 

REMOVAL/INSTALLATION [MZI-

3.5]

 .)

No

Go to the next step.

10

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 
PROCEDURE". 

(See 

AFTER REPAIR 

PROCEDURE [MZI-3.5]

.) 

z

Are any DTC present?  

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

No

Troubleshooting completed.

DTC P0506

IAC system RPM lower than expected

DETECTION 
CONDITION

 

z

This DTC is set when the PCM detects an engine idle speed that is less than 

the desired engine speed.  

z

Engine mechanical concern  

z

Intake air restriction  

z

Exhaust restriction  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:33 AM

Page 258 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Brand: Eaton Pages: 65
iDataLink ADS-ALCA Install Manuals preview
ADS-ALCA
Brand: iDataLink Pages: 30
Porsche 911 GT3 - Brochure preview
911 GT3 -
Brand: Porsche Pages: 51
Whispbar K710W Fitting Instructions For Basic Carrier preview
K710W
Brand: Whispbar Pages: 14
Wagan 2227-1 User Manual preview
2227-1
Brand: Wagan Pages: 8
Thermo King T- series Driver Manual To Simple Operation preview
T- series
Brand: Thermo King Pages: 2
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Brand: Ford Pages: 38
TATA Motors tigor Owner'S Manual preview
tigor
Brand: TATA Motors Pages: 159
Inbay 241170-53-1 Installation Manual preview
241170-53-1
Brand: Inbay Pages: 20
Rago FABRICATION R2223TTUNDM Installation Manual preview
R2223TTUNDM
Brand: Rago FABRICATION Pages: 10
StowAway 2 025.41 Assembly Instructions preview
025.41
Brand: StowAway 2 Pages: 2
Yakima K1249 Instructions Manual preview
K1249
Brand: Yakima Pages: 9
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Brand: Gator Pages: 8
benbat BM721 Instructions For Use Manual preview
BM721
Brand: benbat Pages: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Brand: SPL Pages: 5
Omix-Ada Alloy Rugged Ridge X-Clamp Manual preview
Alloy Rugged Ridge X-Clamp
Brand: Omix-Ada Pages: 2
Dodge 8W-70 Wiring Diagram preview
8W-70
Brand: Dodge Pages: 3
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91

Brands by name

Popular brands

Load more brands