Mazda CX-9 Grand Touring 2007 Manual Download Page 895

Page: 895 / 1056

NO.22 VIBRATION CONCERNS (ENGINE) [MZI-3.5]

DESCRIPTION AND POSSIBLE CAUSES

DIAGNOSTIC PROCEDURE

DIAGNOSTIC INDEX

Spark plug looseness

Intake-air system leakage

Go to the next step.

Is a rapping or roar noise present?

Yes

Inspect looseness for followings:

Dynamic dumper

Intake-air system

Exhaust system

Go to the next step.

Is a knocking noise present?

Yes

Go to symptom troubleshooting "No.13

Knocking/pinging".

(See

NO.13 KNOCKING/PINGING-

ACCELERATION/CRUISE [MZI-

3.5]

If the noise comes from the engine
internal, inspect for friction gear, timing

chain or MLA noise.

Verify test results.

{

If normal, return to diagnostic index to service any additional symptoms.

(See

ENGINE SYMPTOM TROUBLESHOOTING [MZI-3.5]

{

If malfunction remains, inspect related Service Bulletins and/or On-line Repair
Information and perform repair or diagnosis.

If vehicle is repaired, troubleshooting completed.

If vehicle is not repaired or additional diagnostic information is not
available, replace the PCM.

(see

PCM REMOVAL/INSTALLATION [MZI-3.5]

VIBRATION CONCERNS (ENGINE)

DESCRIPTION

Vibration from under hood or driveline

POSSIBLE CAUSE

Loose attaching bolts or worn parts

Components malfunction such as worn parts

STEP INSPECTION

RESULTS ACTION

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 78

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands