Mazda CX-9 Grand Touring 2007 Manual Download Page 465

Page: 465 / 1056

HAS BEEN RECORDED

Has FREEZE FRAME DATA

been recorded?

Record FREEZE FRAME DATA on the
repair order, then go to the next step.

VERIFY RELATED REPAIR
INFORMATION AVAILABILITY

Verify related Service Bulletins
and/or on-line repair information

availability.

Is any related Service Bulletins
available?

Yes

Perform repair or diagnosis according to
the available Service Bulletins.

If the vehicle is not repaired, go to
the next step.

Go to the next step.

VERIFY RELATED PENDING

CODE OR STORED DTCS

Turn the ignition switch off then

to the ON position (Engine off).

Verify related PENDING CODE
or stored DTCs.

Are any DTCs present other than

the following:

{

P0172, P0175, P2196 or
P2198?

Yes

Go to the appropriate DTC troubleshooting

procedures.
(See

DTC TABLE [MZI-3.5]

Go to the next step.

INSPECT ENTIRE INTAKE AIR

SYSTEM FOR DEBRIS,
BLOCKAGE OR OTHER DAMAGE

Check the intake air system for
obstructions, restrictions, and

damage.

Check the throttle plate for
obstructions or sludge.

Check the air filter element and

housing for blockage.

Is a concern present?

Yes

Repair if necessary.

Then go to Step 9.

Go to the next step.

INSPECT FUEL PRESSURE

WARNING:

Fuel line spills and leakage are
dangerous. Fuel can ignite and

cause serious injuries or death.
Fuel can also irritate skin and

eyes. To prevent this, always
complete the "BEFORE REPAIR

PROCEDURE".

Yes

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:30 AM

Page 118

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands