manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

OPERATION TEST 

1. Follow "BEFORE SERVICE PRECAUTION" before performing any work operations to prevent fuel 

from spilling from the fuel system. (See 

BEFORE REPAIR PROCEDURE [MZI-3.5]

.)  

2. Remove the fuel-filler cap. (See 

FUEL TANK REMOVAL/INSTALLATION [MZI-3.5]

.)  

3. Start the fuel pump using the following procedure:  

Using M-MDS 

1. Connect the M-MDS to the DLC-2.  
2. Turn the ignition switch to the ON position. 

Fig. 32: Identifying DLC-2 Connector

 

Courtesy of MAZDA MOTORS CORP.

 

3. Using the simulation function FP, verify that operation sound is heard from the fuel pump when FP is 

turned from OFF to ON. 

z

If the operation sound cannot be verified, measure the voltage at fuel pump wiring harness-side 
connector terminal B. 

„

If as specified, inspect the following: 

z

Fuel pump continuity  

„

If not within the specification, inspect the following: 

z

Fuel pump relay  

z

Wiring harnesses and connectors between battery-fuel pump relay- fuel pump 

NOTE:

z

To improve start ability, the fuel pump control operates the fuel pump unit 

when the ignition switch is turned to the ON position. Due to this, fuel 
pressure is rapidly increased and fuel control is stabilized.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Fuel System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:24:12 AM

Page 26 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

Calira 811 Manual preview
811
Brand: Calira Pages: 14
Axxess AX-DSPX-HYKIA2 Installation Instructions preview
AX-DSPX-HYKIA2
Brand: Axxess Pages: 4
Vintage Air 473275 Manual preview
473275
Brand: Vintage Air Pages: 14
Yakima StickUp Installation Instructions Manual preview
StickUp
Brand: Yakima Pages: 21
Harman Kardon DP 2US Quick Start Manual preview
DP 2US
Brand: Harman Kardon Pages: 16
TATA Motors TIAGO XZ 2019 Owner'S Manual preview
TIAGO XZ 2019
Brand: TATA Motors Pages: 184
B&G electronics PW-50C Civilian Installation And Operation Manual preview
PW-50C Civilian
Brand: B&G electronics Pages: 7
STARLANE POLE STAR PRO Installation And Instruction Manual preview
POLE STAR PRO
Brand: STARLANE Pages: 24
GARO Wallbox GLB Quick Start Manual preview
Wallbox GLB
Brand: GARO Pages: 15
Thule Kit 1312 Instructions Manual preview
Kit 1312
Brand: Thule Pages: 8
Mobridge DA-G2 MOST150 Manual preview
DA-G2 MOST150
Brand: Mobridge Pages: 20
Toyota 2012 Sienna Owner'S Manual preview
2012 Sienna
Brand: Toyota Pages: 779
Fabbri BICI OK 2 Manual preview
BICI OK 2
Brand: Fabbri Pages: 32
Whelen Engineering Company SAK34 Installation Manual preview
SAK34
Brand: Whelen Engineering Company Pages: 2
Subaru 2015 Forester Quick Reference Manual preview
2015 Forester
Brand: Subaru Pages: 16
CITROEN 2 CV4 Owner'S Manual preview
2 CV4
Brand: CITROEN Pages: 86
Toyota Tacoma 05 Brochure & Specs preview
Tacoma 05
Brand: Toyota Pages: 26
GEMINI TECHNOLOGY 514F User Manual preview
514F
Brand: GEMINI TECHNOLOGY Pages: 9

Brands by name

Popular brands

Load more brands