Mazda CX-9 Grand Touring 2007 Manual Download Page 849

Page: 849 / 1056

B1681, B2103, B1213

Inspect the following wiring harnesses

and connectors:
With advanced keyless entry system:

Between coil terminal A and

keyless control module terminal
3V

Between coil terminal B and

keyless control module terminal
3U

Without advanced keyless entry

system:

Between coil terminal A and

instrument cluster terminal 1G

Between coil terminal B and
instrument cluster terminal 1E

Is there any malfunction?

Yes

Repair or replace the suspected wiring

harness and connector.

Go to the next step, (with advanced
keyless entry system.)

Go to Step 8. (without advanced keyless

entry system.)

Inspect the following wiring harnesses
and connectors for an open or short

circuit:

Between keyless control module

terminal 3W and instrument
cluster terminal 1W

Between keyless control module

terminal 3X and instrument
cluster terminal 1X

Is there any malfunction?

Yes

Repair or replace wiring harness and
connectors.

Go to the next step.

Inspect the following wiring harnesses

and connectors:

Between PCM terminal 1BG and

instrument cluster terminal 1W

Between PCM terminal 1BL and
instrument cluster terminal 1X

Yes

Repair or replace the suspected wiring

harness and connector.

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 32

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands