manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

7

INSPECT GENERATOR CIRCUIT 
FOR OPEN CIRCUIT

 

z

Inspect the continuity between 
generator terminal B (wiring 

harness-side) and battery positive 
terminal (wiring harness-side)  

z

Is there continuity?  

Yes

Go to the next step.

No

Repair or replace suspected part, then go to 

Step 10.

8

INSPECT PCM CONNECTOR FOR 

POOR CONNECTION

 

z

Turn the engine switch off.  

z

Inspect for poor connection (such 

as damaged/pulled-out terminals, 
corrosion).  

z

Are there any malfunction?  

Yes

Repair or replace suspected part, then go to 

Step 10.

No

Go to the next step.

9

INSPECT GENERATOR

 

z

Inspect the generator. 

(see 

GENERATOR 

INSPECTION [MZI-3.5]

 .) 

z

Is there any malfunction?  

Yes

Replace the generator, then go to Step 10.

(see 

GENERATOR 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

10

VERIFY TROUBLESHOOTING OF 
DTC P0625 HAS BEEN 

COMPLETED

 

z

Verify that all disconnected 

connectors reconnected.  

z

Clear the DTC from the PCM 
memory using the M-MDS.  

z

Perform the "KOEO or KOER 

self-test" using the M-MDS. 

(See 

KOEO/KOER SELF TEST 

[MZI-3 51

.) 

z

Is the PENDING CODE for the 
DTC present?  

Yes

Replace the PCM, then go to the next step.
(see 

PCM 

REMOVAL/INSTALLATION [MZI-
3.5]

 .)

No

Go to the next step.

11

VERIFY AFTER REPAIR 

PROCEDURE

 

z

Perform the "AFTER REPAIR 

PROCEDURE". 

Yes

Go to the applicable DTC inspection. 

(See 

DTC TABLE [MZI-3.5]

.)

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:26:35 AM

Page 307 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

A-Tach Mounts ST-1 Instructions preview
ST-1
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50291 Quick Start Manual preview
50291
Brand: A-Tach Mounts Pages: 2
A-Tach Mounts 50206 Instructions preview
50206
Brand: A-Tach Mounts Pages: 2
IAME Parilla X30 Assembly Instructions And User'S Manual preview
Parilla X30
Brand: IAME Pages: 17
PAC RadioPRO 5 RP5-GM41 Quick Start Manual preview
RadioPRO 5 RP5-GM41
Brand: PAC Pages: 3
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Brand: Tesla Pages: 9
Vintage Air 561163 Manual preview
561163
Brand: Vintage Air Pages: 28
Edelbrock 6883 Instructions preview
6883
Brand: Edelbrock Pages: 2
Eaton Green Motion DC 66 User Manual preview
Green Motion DC 66
Brand: Eaton Pages: 18
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Brand: Dakota Digital Pages: 3
Meta System 900000358 Installation Technical Sheet preview
900000358
Brand: Meta System Pages: 22
UAZ 2001 ???-3741 Instruction Manual preview
2001 ???-3741
Brand: UAZ Pages: 112
Havis C-DMM-3005 Installation Instructions preview
C-DMM-3005
Brand: Havis Pages: 5
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Brand: APS Pages: 3
Jeep WRANGLER 2017 User Manual preview
WRANGLER 2017
Brand: Jeep Pages: 292
KLAUS Multiparking trendvario6X00 Service Manual preview
trendvario6X00
Brand: KLAUS Multiparking Pages: 72
Connects2 CTUPO01 Quick Start Manual preview
CTUPO01
Brand: Connects2 Pages: 8
Brink 5978 Fitting Instructions Manual preview
5978
Brand: Brink Pages: 21

Brands by name

Popular brands

Load more brands