Mazda CX-9 Grand Touring 2007 Manual Download Page 683

Page: 683 / 1056

DTC P1001 [MZI-3.5]

DTC P1001 (MZI-3.5) DETECTION CONDITION AND POSSIBLE CAUSES

DIAGNOSTIC PROCEDURE

DTC P1001 (MZI-3.5) DIAGNOSTIC PROCEDURE

Has the customer requested DTC

P1000 be cleared from the PCM

memory?

(See

OBD-II DRIVE MODE [MZI-

3.5]

Inform customer that if the law in the
state requires additional driving in order

to clear DTC P1000 from the PCM
memory, it must be performed before an

inspection maintenance test.

VERIFY AFTER REPAIR
PROCEDURE

Perform the "AFTER REPAIR
PROCEDURE".

(See

AFTER REPAIR

PROCEDURE [MZI-3.5]

Are any DTC present?

Yes

Go to the applicable DTC inspection.
(See

DTC TABLE [MZI-3.5]

Troubleshooting completed.

DTC P1001

KOER not able to complete, KOER aborted

DETECTION

CONDITION

P1001 indicates any of the following

Unable to access Continuous Memory DTCs.

Unable to activate KOEO or KOER Self-Test.

M-MDS tester communication problem.

DTC displayed by M-MDS tester not listed.

KOER Self-Test cannot be completed.

POSSIBLE CAUSE

Damaged DLC-2.

Incorrect Self-Test procedure.

VREF is not in specification.

Idle RPM out of specification.

Open in DLC-2 wiring harness circuit.

Short in DLC-2 circuit or associated modules.

Damaged PCM power relay circuit

STEP

INSPECTION

ACTION

VERIFY FREEZE FRAME DATA
HAS BEEN RECORDED

Yes

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE On-Board Diagnostic (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:26:36 AM

Page 336

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands