Mazda CX-9 Grand Touring 2007 Manual Download Page 848

Page: 848 / 1056

DIAGNOSTIC PROCEDURE

STEP INSPECTION

RESULTS ACTION

Connect the M-MDS to the DLC-2.
Do any of the following conditions

appear?

Engine does not completely
start.

DTC P1260 is displayed.

Yes

Both conditions appear:

Go to Step 3.

Either or other condition appears:

Go to the next step.

Does engine stall after

approx. 2 s

from when it is started?

Yes

Go to the next step.

Immobilizer system is normal.
Go to Step 8.

Is the coil connector securely

connected to the coil?

Yes

Go to the next step.

Connect the coil connector securely.
Return to Step 2.

Does the security light flush?

Yes

Go to the next step.

Inspect and repair or replace the

following:

Wiring harnesses and connectors

from keyless control module
terminal 3W and instrument

cluster terminal 1W

Wiring harness and connectors
from keyless control module

terminal 3X and instrument cluster
terminal 1X

Instrument cluster

(see

INSTRUMENT CLUSTER

INSPECTION

Connect the M-MDS to the DLC-2 and
retrieve the DTC for PCM, instrument

cluster and keyless control module
(with advanced keyless entry system).

Are any of the following DTCs
displayed?

DTC

PCM: B1342, U0073, U0155

Instrument cluster: B1213, B1600,
B1601, B1602, B1681, B2103, B2139,

B2431, U0100, U0214

Keyless control module (with

advanced keyless entry system):

Yes

Go to the appropriate DTC inspection.
(see

DTC TABLE [MZI-3.5]

Go to the next step.

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:37 AM

Page 31

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands