manualshive.com logo in svg

Mazda CX-9 Grand Touring 2007, Manual

The Mazda CX-9 Grand Touring 2007 Manual is available for free download on manualshive.com. This comprehensive user manual provides essential information and instructions to operate and maintain your Mazda CX-9 Grand Touring. Easily access this informative resource to enhance your driving experience and ensure optimal performance of your vehicle.

Share
Download
background image

1. Level the vehicle.  
2. Complete the "BEFORE REPAIR PROCEDURE". (See 

BEFORE REPAIR PROCEDURE [MZI-

3.5]

.)  

3. Disconnect the negative battery cable. (see 

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

 .)  

4. Remove the engine cover. (see 

ENGINE COVER REMOVAL/INSTALLATION [MZI-3.5]

 .)  

5. Remove the fuel line schrader valve cap.  
6. Connect a long hose to the disconnected schrader valve cap and drain the fuel into a container used for 

collecting gasoline.  

7. Start the fuel pump using the following procedure. 

Using M-MDS

  

1. Connect the negative battery cable. (see 

BATTERY REMOVAL/INSTALLATION [MZI-3.5]

.) 

serious injuries or death and damage. Fuel can also irritate skin and 

eyes. To prevent this, always complete the "Fuel Line Safety 
Procedure".  

z

Fuel line spills and leakage are dangerous. Fuel can ignite and cause 
serious injuries or death and damage. Fuel can also irritate skin and 

eyes. To prevent this, before performing the fuel pump unit 
removal/installation, always complete the "Fuel Leak Inspection 

After Fuel Pump Unit Installation".  

z

A person charged with static electricity could cause a fire or 

explosion, resulting in death or serious injury. Before draining fuel, 
make sure to discharge static electricity by touching the vehicle 

body.  

CAUTION:

z

Because the fuel tank is constructed such that the fuel level is higher 

than the installation surface of the fuel pump, fuel leakage could 
occur. If the fuel gauge indicates a fuel level of 3/4 or more, perform 

the following Steps 3-8 to drain 10-15 L {2.7-3.9 US gal, 2.2-3.2 Imp 
gal} of fuel.  

z

Disconnecting/connecting the quick release connector without 
cleaning it may possibly cause damage to the fuel pipe and quick 

release connector. Always clean the quick release connector joint 
area before disconnecting/connecting using a cloth or soft brush, 

and make sure that it is free of foreign material.  

 

2007 Mazda CX-9 Grand Touring 

2007 ENGINE PERFORMANCE Fuel System (MZI-3.5) - CX-9

  

Microsoft 

 

Sunday, November 15, 2009 9:24:12 AM

Page 22 

© 2005 Mitchell Repair Information Company, LLC. 

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CX-9 Grand Touring 2007

GARO TWIN+ Assembly Instructions / End User Instruction preview
TWIN+
Brand: GARO Pages: 23
GARO LS4 Wallmounted Operational Instructions preview
LS4 Wallmounted
Brand: GARO Pages: 15
Vauxhall 2009 Tigra Quick Reference Manual preview
2009 Tigra
Brand: Vauxhall Pages: 2
SAF-HOLLAND FleetMaster Air FW8 Series Owner'S Manual preview
FleetMaster Air FW8 Series
Brand: SAF-HOLLAND Pages: 20
FormFit HD 10L07 Installation Instructions preview
HD 10L07
Brand: FormFit Pages: 2
V8 equipment EBEX.2 Instruction Manual preview
EBEX.2
Brand: V8 equipment Pages: 17
Dacia 2014 Sandero Driver'S Handbook Manual preview
2014 Sandero
Brand: Dacia Pages: 238
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Brand: MAcarbon Pages: 4
Volvo S90 2018 Quick Manual preview
S90 2018
Brand: Volvo Pages: 42
Dodge 2005 JR41 Stratus Owner'S Manual preview
2005 JR41 Stratus
Brand: Dodge Pages: 293
Oypla Leisure 4269 User Manual preview
4269
Brand: Oypla Leisure Pages: 4
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Brand: Rugged Ridge Pages: 3
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Brand: Mercedes-Benz Pages: 91
Weltmann KFZ-Teile 9B500016 Fitting Instructions Manual preview
9B500016
Brand: Weltmann KFZ-Teile Pages: 12
v.link VL2-DVD900 Manual preview
VL2-DVD900
Brand: v.link Pages: 19
NavLinkz RL4-ELINK Manual preview
RL4-ELINK
Brand: NavLinkz Pages: 23
Calix M5T 204 Assembly Instructions preview
M5T 204
Brand: Calix Pages: 4
EUFAB 12014 Manual preview
12014
Brand: EUFAB Pages: 20

Brands by name

Popular brands

Load more brands