Mazda CX-9 Grand Touring 2007 Manual Download Page 831

Page: 831 / 1056

DTC P1260 is displayed.

Turn the ignition switch to the ON
position.

Is the coil connector securely connected
to the coil?

Yes

Go to the next step.

Connect the coil connector securely.

Return to Step 1.

Does the security light flush?

Yes

Go to the next step.

Inspect and repair or replace the
following:

Wiring harnesses and connectors

from keyless control module
terminal 3W and instrument

cluster terminal 1W

Wiring harness and connectors
from keyless control module

terminal 3X and instrument
cluster terminal 1X

Instrument cluster

(see

INSTRUMENT

CLUSTER INSPECTION

Connect the M-MDS to the DLC-2 and

retrieve DTC for PCM, instrument
cluster and keyless control module.

DTC

PCM: B1342, U0073, U0155

Instrument cluster: B1213, B1600,
B1601, B1602, B1681, B2103, B2139,

B2431, U0100, U0214

Keyless control module (with

advanced keyless entry system):

B1681, B2103, B1213

Yes

Go to appropriate DTC inspection.

(see

DTC TABLE [MZI-3.5]

Go to the next step.

Inspect for the following wiring
harnesses and connectors:

With advanced keyless entry system

Between coil terminal A and
keyless control module terminal

Between coil terminal B and

keyless control module terminal
3U

Without advanced keyless entry

Yes

Repair or replace suspected wiring
harness and connector.

Go to the next step, (with advanced
keyless entry system)

Go to the Step 8. (without advanced
keyless entry system)

2007 Mazda CX-9 Grand Touring

2007 ENGINE PERFORMANCE Symptom Troubleshooting (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:27:36 AM

Page 14

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands