Mazda CX-9 Grand Touring 2007 Manual Download Page 251

Page: 251 / 1056

Fig. 93: Installing Front Oil Seal

Courtesy of MAZDA MOTORS CORP.

CRANKSHAFT PULLEY INSTALLATION NOTE

1. Install the crankshaft pulley, washer, and

SST

to the crankshaft.

Fig. 94: Identifying Crankshaft Pulley, Washer, And SST

Courtesy of MAZDA MOTORS CORP.

2. Tighten the

SST

nut and install the crankshaft pulley.

NOTE:

Lubricate the contact surface (exterior area of inner diameter) of the front
oil seal with clean engine oil.

2007 Mazda CX-9 Grand Touring

2007 ENGINE Mechanical (MZI-3.5) - CX-9

Microsoft

Sunday, November 15, 2009 9:19:27 AM

Page 60

Summary of Contents for CX-9 Grand Touring 2007

































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands

Mazda CX-9 Grand Touring 2007, Manual

Search results

Summary of Contents for CX-9 Grand Touring 2007

Reviews:

Related manuals for CX-9 Grand Touring 2007

Brands by name

Popular brands