background image

2009-13 Toyota Corolla 

Installation Instructions

BX3781

405-0009 Rev. C 

Page 1 of 7 

3/1/12

1.   Blue Ox

®

 towing products and accessories  

      are intended to be installed by Blue Ox

® 

 

      Dealers who are familiar with our products and 

      have the equipment and knowledge to do “fit 

 

      work.” When necessary, Blue Ox

®

 Dealers can  

      be found at 

www.blueox.com 

or by contacting 

      our Customer Care Department at
      (800)228-9289.

2.   Many Blue Ox

®

 Baseplates are designed to  

      use existing holes and hardware to mount  
      the baseplate to the towed vehicle. Even 
      though bolts are there, do not assume they  
      are adequate for baseplate mounting. Always 
      use hardware supplied in the hardware kit  

      or existing hardware specified in the 

 

      Baseplate Towing Installation Instructions. 

Serial Number

Confirm the towability and pre-towing 

procedures for your vehicle with 

the owner’s manual or contact the 

vehicle’s manufacturer for specific 

towing procedures.

Please read BOTH these Installation Instructions and the General Towing Instructions 

before attempting to install or operate this equipment.

!

Failure to read and follow these instructions 

could result in separation of the towed vehicle 

from the tow bar, causing property damage, 

loss of towed vehicle, personal injury or death.

WARNING

Attachment Tab Height: 

15”

Attachment Tab Width: 

18 1/4”

Bolt Torque Specifications 

Torque in Foot-Pounds per Inch Bolts

 

Bolt Torque Specifications 

Torque in Foot-Pounds per Metric Bolts 

Bolt Size Grade 8.8 Grade 10.9

6MM

6

8

8MM

16

22

10MM

31

40

12MM

54

70

14MM

89

117

Bolt Size

Grade 5

Grade 8

1/4”

10

14

5/16”

19

29

3/8”

33

47

7/16”

54

78

1/2”

78

119

5/8”

154

230

Summary of Contents for BX3781








Reviews: