manualshive.com logo in svg

Siemens SIMODRIVE 611 universal, Руководство по эксплуатации функций


Поделиться
Скачать
background image

6

6.15 Spindle positioning (from SW 5.1)

6-608

 Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

The target position approach is defined using the parameters of the
selected traversing block.

Table 6-71

Parameters for ”spindle positioning”

Parame-

ters

Parameter text

Value and description

P0080:N

Block number

0... 63

P0081:N

Item

Target position in degrees

P0082:N

Velocity

Search velocity in degrees/min. The velocity is always referred to the load
side, i.e. for a ratio of 4:1 (motor/load), the motor rotates 4 x faster.

P0083:N

Acceleration
override

This allows the acceleration to be influenced, referred to P0103.

P0084:N

Deceleration
override

This allows the deceleration to be influenced, referred to P0104.

P0087:N

Mode

U0W0

Hex 

U = target position input

0: Input via traversing block (P0081:N)
1: Input via PROFIBUS–DP; control word XSP (Signal No. 50109)

W = Positioning mode

The behavior when approaching the target position is defined in parame-
ter P0087. The behavior depends on whether the ”spindle positioning”
function is already active and the 1st position was approached or not.

Behavior for nset 
active

Behavior if the
1st target position
has already been reached

W = 0 ABSO-
LUTE
(Standard)

The position is ap-
proached with the
actual direction of
rotation

The new target position is ap-
proached through the short-
est distance

W = 1 RELATIVE

Not possible

The new position is incremen-
tally approached.

W = 2 ABS_POS

The position is
approached in the
positive direction.

The new target position is ap-
proached in absolute terms
and in the positive direction
(clockwise rotation)

W = 3 ABS_NEG

The position is
approached in the
negative direction.

The new target position is ap-
proached in absolute terms
and in the negative direction
(counter–clockwise).

Approaching the
target position
using the
traversing block
parameters

6  Description of the Functions

01.99

02.02

! not 611ue !

02.03

Содержание SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMODRIVE 611 universal

Balboa GL Series User Manual preview
GL Series
Бренд: Balboa Страницы: 12
Paoli F1 Operating And Maintenance Manual preview
F1
Бренд: Paoli Страницы: 16
Saitek X36 Manual preview
X36
Бренд: Saitek Страницы: 4
tams elektronik ABC-1 Manual preview
ABC-1
Бренд: tams elektronik Страницы: 12
Union Instruments CWD2005 SPC Operating Instructions And Safety Notes preview
CWD2005 SPC
Бренд: Union Instruments Страницы: 63
Zaiput Flow Technologies BPR-1000 Instruction Manual preview
BPR-1000
Бренд: Zaiput Flow Technologies Страницы: 10
Dantherm HRC 2 User Manual preview
HRC 2
Бренд: Dantherm Страницы: 28
Midland A-14167 Series Installation, Operation & Maintenance Manual preview
A-14167 Series
Бренд: Midland Страницы: 37
Sensitron ST.PL4+ Installation And User Manual preview
ST.PL4+
Бренд: Sensitron Страницы: 32
Dantherm HCP 11 Installation And User Manual preview
HCP 11
Бренд: Dantherm Страницы: 36
Simplex 4006-9101 Technical Manual preview
4006-9101
Бренд: Simplex Страницы: 78
Comunello CU-24V-1M Installation And User Manual preview
CU-24V-1M
Бренд: Comunello Страницы: 13
Levven GPC20 Instruction Sheet preview
GPC20
Бренд: Levven Страницы: 2
DEUTSCHMANN AUTOMATION LOCON 100 Instruction Manual preview
LOCON 100
Бренд: DEUTSCHMANN AUTOMATION Страницы: 30
salmson EC-Drain 2x4,0 Installation And Starting Instructions preview
EC-Drain 2x4,0
Бренд: salmson Страницы: 37
audiowireless DADM226 Quick Setup Manual preview
DADM226
Бренд: audiowireless Страницы: 2
Belimo GM24A-MOD Technical Data Sheet preview
GM24A-MOD
Бренд: Belimo Страницы: 6
Viconics VT76 7 Series Installation Manual preview
VT76 7 Series
Бренд: Viconics Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды