manualshive.com logo in svg

Siemens SIMODRIVE 611 universal, Руководство по эксплуатации функций


Поделиться
Скачать
background image

6

6.2

Positioning mode (P0700 = 3, from SW 2.1)

6-407

 Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

Note

The following is valid when jogging:

The traversing direction is defined by the sign of P0108 or P0109.

When the jogging signal is withdrawn, the axis comes to an
immediate stop and, at the next ”1” signal is re–started with the
same task.

It is not possible to continue after incremental jogging has been
interrupted.

The software limit switches are effective if they have been activated
and set for this axis, and the axis has been referenced. Contrary to
operation in the positioning mode, the axis only starts to brake
when the software limit switch is reached. The travel beyond the
software limit switch depends on the active velocity setpoint for
jogging 1/2 (P0108/P0109, override) and the selected maximum
deceleration (P0104).

The override is effective.

If input signals for jogging 1 and 2 are simultaneously available,
then an appropriate fault is signaled.

If the position reference value is inverted (P0231, P0232), then the
direction of rotation also changes in the jogging mode.

For speed–controlled jogging, the drive is in the tracking status. In
this case, the velocity setpoint and actual 
value are formed from the speed controller.

The following parameters are available for the ”jogging mode” function:

P0108

Velocity setpoint, jogging 1

P0109

Velocity setpoint, jogging 2

P0122

Jogging 1, increments (from SW 4.1)

P0123

Jogging 2, increments (from SW 4.1)

The following signals are available for the ”jogging mode” function:

Input signals
(refer under index entry ”Input signal, digital – ...”)

– Input signal ”jogging 1 ON/jogging 1 OFF”

––> using an input terminal with function number 62

––> via PROFIBUS control signal ”STW1.8”

– Input signal ”jogging 2 ON/jogging 2 OFF”

––> using an input terminal with function number 63

––> via PROFIBUS control signal ”STW1.9”

– Input signal, ”incremental jogging ” (from SW 4.1)

––> using an input terminal with function number 61

––> via the PROFIBUS control signal ”PosStw.5”

Parameter
overview
(refer to Chapter
A.1)

Input signals (refer
to Chapter 6.4)

6  Description of the Functions

01.99

! not 611ue !

02.02

Содержание SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMODRIVE 611 universal

Lawler 802 Installation & Maintenance Manual preview
802
Бренд: Lawler Страницы: 5
Walchem W100 Troubleshooting Manual preview
W100
Бренд: Walchem Страницы: 10
Tapeswitch C6 Technical Manual preview
C6
Бренд: Tapeswitch Страницы: 13
Canarm MC Series Installation Manual preview
MC Series
Бренд: Canarm Страницы: 3
Parker ER Series Maintenance Instructions & Parts List preview
ER Series
Бренд: Parker Страницы: 44
Hama Thunder V18 Instruction Manual preview
Thunder V18
Бренд: Hama Страницы: 12
Hama Thunder V18 Operating Instruction preview
Thunder V18
Бренд: Hama Страницы: 12
Hama Mini V3 Rumble Operating Instruction preview
Mini V3 Rumble
Бренд: Hama Страницы: 14
Hama Dual Vibration Operating Instruction preview
Dual Vibration
Бренд: Hama Страницы: 8
Eaton FC18 User Manual preview
FC18
Бренд: Eaton Страницы: 10
Idemia SIGMA Series Quick User Manual preview
SIGMA Series
Бренд: Idemia Страницы: 29
Sunnen HTA-2000 (2M) Manual preview
HTA-2000 (2M)
Бренд: Sunnen Страницы: 24
ZKTeco LockerPad-7B User Manual preview
LockerPad-7B
Бренд: ZKTeco Страницы: 27
Sunlight Supply TITAN CONTROLS KRONUS 2 Instruction Manual preview
TITAN CONTROLS KRONUS 2
Бренд: Sunlight Supply Страницы: 4
Secutron MR-2320 Series Installation And Operation Manual preview
MR-2320 Series
Бренд: Secutron Страницы: 92
Fermax LYNX SKYLINE Installer Manual preview
LYNX SKYLINE
Бренд: Fermax Страницы: 68
JBL Six Button Remote User Manual preview
Six Button Remote
Бренд: JBL Страницы: 5
A-T Controls Triad Controls WE Series Installation And Operation Manual preview
Triad Controls WE Series
Бренд: A-T Controls Страницы: 13

Бренды по названию

Популярные бренды

Загрузить еще бренды