manualshive.com logo in svg

Siemens SIMODRIVE 611 universal, Руководство по эксплуатации функций


Поделиться
Скачать
background image

5

5.8

Motion Control with PROFIBUS–DP (from SW 3.1)

5-295

 Siemens AG 2005 All Rights Reserved

SIMODRIVE 611 universal Description of Functions (FBU) – 04.05 Edition

5.8.1

Equidistant DP cycle operation in the n–set mode

With the function, the closed–position control loop is closed through
PROFIBUS. The position controller is in the DP master, the closed–
loop current and speed control as well as the position actual value sen-
sing (encoder interface) are in the DP slave.

The position controller clock cycle is transferred to the DP slaves via
the fieldbus, and the slaves synchronize their speed/current controller
clock cycle to the position controller clock cycle of the DP master.

The DP master enters the speed setpoint.

The motor encoder or another measuring system can be used for the
position actual value sensing in the DP slave.

Direct measuring system at X412  ––> 

Encoder 2
(from SW 3.3)

Additional measuring system at X472 

––>  Encoder 3

TTL encoder, P0890 = 4, only SIMODRIVE 611 universal E

The encoder interface must be configured in the process data.

––> Refer to Chapter 5.6.5

n

set

Clo
ck
cycl
e

x

act

Current
control

Speed
control

M 

∼

G

G

Motor
encoder
at X411/X412

n

set

Clo
ck
cycl
e

x

act

Current
control

Speed
control

M 

∼

G

G

Motor
encoder
at X411/X412

n

set

DP master with
the ”Motion
Control with
PROFIBUS–DP”
function

e.g. 
SINUMERIK
802D

Clock
cycle

x

act

PROFIBUS–DP

Current
control

Speed
control

M 

∼

G

Position control loop

G

Measuring system

(encoder 2 or 3)

Motor encoder
at X411/X412

DP slave 611U

Fig. 5-25 Overview for ”motion control with PROFIBUS–DP”: Example with DP master and 3 DP slaves

Overview

5  Communications via PROFIBUS DP

08.99

Содержание SIMODRIVE 611 universal



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SIMODRIVE 611 universal

Eaton i-on Compact Quick Setup Manual preview
i-on Compact
Бренд: Eaton Страницы: 12
Parker A4W Series Installation And Service Information preview
A4W Series
Бренд: Parker Страницы: 12
YOKOGAWA UT35A-L User Manual preview
UT35A-L
Бренд: YOKOGAWA Страницы: 150
YOODA NANO Series Quick Start Manual preview
NANO Series
Бренд: YOODA Страницы: 3
YMGI 584 Series User Manual preview
584 Series
Бренд: YMGI Страницы: 8
Universal Remote Genesis MX-900 Manual preview
Genesis MX-900
Бренд: Universal Remote Страницы: 20
Panasonic KX-A16B Quick Start Manual preview
KX-A16B
Бренд: Panasonic Страницы: 8
Belden GRASS VALLEY MDX-3901 Manual To Installation And Operation preview
GRASS VALLEY MDX-3901
Бренд: Belden Страницы: 45
Vag RIKO Operating And Maintenance Instructions Manual preview
RIKO
Бренд: Vag Страницы: 12
Osram traxon e:cue LCE-mx Setup Manual preview
traxon e:cue LCE-mx
Бренд: Osram Страницы: 35
Waterbird ITSC1000 User Manual preview
ITSC1000
Бренд: Waterbird Страницы: 19
Logitech 963321-0403 - Cordless Precision Controller Installation Manual preview
963321-0403 - Cordless Precision Controller
Бренд: Logitech Страницы: 1
MOBA MOBA-Matic MMC-1000 User Manual preview
MOBA-Matic MMC-1000
Бренд: MOBA Страницы: 172
Vimar Elvox R854 Installer'S Manual preview
Elvox R854
Бренд: Vimar Страницы: 8
Nations N32G43 Series User Manual preview
N32G43 Series
Бренд: Nations Страницы: 654
GIESSE RACK MAX 650 Instruction And Installation Manual preview
RACK MAX 650
Бренд: GIESSE Страницы: 136
HydroQuip BALBOA CS6000B Series Operation Manual preview
BALBOA CS6000B Series
Бренд: HydroQuip Страницы: 32
G-Force CU36B6A Manual preview
CU36B6A
Бренд: G-Force Страницы: 9

Бренды по названию

Популярные бренды

Загрузить еще бренды