Texas Instruments Concerto F28M35 Series Technical Reference Manual Download Page 586 | Manualshive

Page: 586 / 1655

background image

C-Boot ROM Description

586

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

ROM Code and Peripheral Booting

CBROM_MTOC_IPC_INT1_ISR

Below is the procedure that C-Boot ROM, MOTCIPCINT1 handler follows in response to IPC command
from master (MTOCIPCINT1).

•

Read and decode the command in MTOCIPCCOM register.

•

Read/decode the address on which C-Boot ROM has to act as per the command.

•

Read/decode the data with which C-Boot ROM has to act on the above address as per the command.

•

Service the command.

•

Clear MTOCIPCFLG[31] if the command was successfully processed, if the command was invalid or
cannot execute the command because of any reason, MTOCIPCFLG[31] is not cleared and
MTOCIPCDATAR register is updated with error code explained in the following sections.

•

Put the result (if any) of the command in MTOCIPCDATAR register, if the command is executed
successfully.

•

Set bit 0 in MTOCIPCACK register. This will clear bit 0 in MTOCIPCFLG register and Master user
application will know that C-Boot ROM has served the command and it can look at MTOCIPCDATAR
register for the result of command.

explains how C-Boot ROM MTOCIPCINT1 handler - cbrom_mtoc_ipc_int1_isr, follows to

service IPC command from Master.

«
...
584
585
586
587
588
...
»

Summary of Contents for Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Concerto F28M35 Series

ControlMaster CM15

Brand: ABB Pages: 4

Brand: Camozzi Pages: 33

Brand: Camozzi Pages: 64

Brand: Datapath Pages: 12

Brand: jbc Pages: 8

Brand: Nabco Pages: 35

Brand: Danfoss Pages: 30

Brand: Aurora Pages: 2

LDSBus LC020101A-F

Brand: BRT Systems Pages: 15

Brand: GeoVision Pages: 21

Brand: 2N Pages: 107

Micro850 series

Brand: Allen-Bradley Pages: 24

Brand: Apricus Pages: 32

Linear Technology ADI Power DC3017A

Brand: Analog Devices Pages: 12

Brand: Swagelok Pages: 6

Brand: AUMA Pages: 48

Nuvo-3000 Series

Brand: Neousys Technology Pages: 101

Brand: Danfoss Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands