manualshive.com logo in svg

Texas Instruments Concerto F28M35 Series, Technical Reference Manual

The Texas Instruments Concerto F28M35 Series is a powerful microcontroller designed for high-performance applications. With its comprehensive Technical Reference Manual available for free download from our website, users can easily access detailed information and instructions to maximize the product's capabilities. Enhance your project with the Concerto F28M35 Series today.

Share
Download
background image

Host Bus Mode

www.ti.com

1200

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

Copyright © 2012–2019, Texas Instruments Incorporated

External Peripheral Interface (EPI)

Host-Bus 8 and Host-Bus 16 modes are very configurable. The user has the ability to connect 1,2, or 4
external devices to the EPI signals, as well as control whether byte select signals are provided in HB16
mode. These capabilities depend on the configuration of the MODE field in the EPIHBnCFG register, the
CSCFG field and the CSCFGEXT bit in the EPIHBnCFGn register, and the BSEL bit in the EPIHB16CFG
register. The CSCFGEXT bit extends the chip select configuration possibilities by providing the most
significant bit of the CSCFG field. Refer to

Table 17-2

for the possible ALE and chip select options that

can be programmed by the combination of the CSCFGEXT and CSCFG bits. Note that CSCFGEXT is the
most significant bit.

Table 17-2. CS CSCFG Encodings

Value

Description

0x0

ALE Configuration
EPI0S30 is used as an address latch (ALE). The ALE signal is generally used when the
address and data are muxed (MODE field in the EPIHB8CFG register is 0x0). The ALE
signal is used by an external latch to hold the address through the bus cycle.

0x1

CS Configuration
EPI0S30 is used as a Chip Select (CS). When using this mode, the address and data are
generally not muxed (MODE field in the EPIHB8CFG register is 0x1). However, if address
and data muxing is needed, the WR signal (EPI0S29) and the RD signal (EPI0S28) can be
used to latch the address when CS is low.

0x2

Dual CS Configuration
EPI0S30 is used as CS0 and EPI0S27 is used as CS1. Whether CS0 or CS1 is asserted is
determined by the most significant address bit for a respective external address map. This
configuration can be used for a RAM bank split between 2 devices as well as when using
both an external RAM and an external peripheral.

0x3

ALE with Dual CS Configuration
EPI0S30 is used as address latch (ALE), EPI0S27 is used as CS1, and EPI0S26 is used as
CS0. Whether CS0 or CS1 is asserted is determined by the most significant address bit for a
respective external address map.

0x4

ALE with Single CS
Configuration EPI0S30 is used as address latch (ALE) and EPI0S27 is used as CS

0x5

Quad CS Configuration
EPI0S30 is used as CS0 and EPI0S27 is used as CS1. EPI0S34 is used as CS2 and
EPI0S33 is used as CS3

0x6

ALE with Quad CS Configuration
EPI0S30 is used as CS0 and EPI0S27 is used as CS1. EPI0S34 is used as CS2 and
EPI0S33 is used as CS3

0x7

Tri CS Configuration.
EPI0S30 is used CS0. EPI0S34 is used as CS2 and EPI0S33 is used as CS3

If one of the dual-chip-select modes is selected (CSCFGEXT is 0x0 and CSCFG is 0x2 or 0x3 in the
EPIHBnCFGn register), both chip selects can share the peripheral, code, or the memory space, or one
chip select can use the peripheral space and the other can use the memory or code space.

In the EPIADDRMAP register, if the EPADR field is not 0x0, the ECADR field is 0x0, and the ERADR field
is 0x0, then the address specified by EPADR is used for both chip selects, with CS0 being asserted when
the MSB of the address range is 0 and CS1 being asserted when the MSB of the address range is 1.

If the ERADR field is not 0x0, the ECADR field is 0x0, and the EPADR field is 0x0, then the address
specified by ERADR is used for both chip selects, with the MSB performing the same delineation.

If both the EPADR and the ERADR are not 0x0, and the ECADR field is 0x0 and the EPI is configured for
dual-chip selects, then CS0 is asserted for either address range defined by EPADR and CS1 is asserted
for either address range defined by ERADR.

The two chip selects can also be shared between the code space and memory or peripheral space. If the
ECADR field is 0x1, ERADR field is 0x0, and the EPADR field is not 0x0, then CS0 is asserted for the
address range defined by ECADR and CS1 is asserted for either address range defined by EPADR.

If the ECADR field is 0x1, EPADR field is 0x0, and the ERADR field is not 0x0, then CS0 is asserted for
the address range defined by ECADR and CS1 is asserted for either address range defined by ERADR.

Summary of Contents for Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Concerto F28M35 Series

National Instruments RMC-8354 User Manual preview
RMC-8354
Brand: National Instruments Pages: 102
NAU ROBOTICS RC40A Operating Instruction preview
RC40A
Brand: NAU ROBOTICS Pages: 109
Native Instruments Maschine Mikro MK2 Getting Started preview
Maschine Mikro MK2
Brand: Native Instruments Pages: 181
Rain Bird Image Series Quick Start Manual preview
Image Series
Brand: Rain Bird Pages: 4
Rain Bird ESP-ME3 Quick Reference Manual preview
ESP-ME3
Brand: Rain Bird Pages: 2
Rain Bird ESP-Me User Manual preview
ESP-Me
Brand: Rain Bird Pages: 140
Raindrip WeatherSmart RSC600i Installation & Programming preview
WeatherSmart RSC600i
Brand: Raindrip Pages: 36
Talgil DREAM 2 Manual preview
DREAM 2
Brand: Talgil Pages: 14
YOKOGAWA TC 10-L Engineering Manual preview
TC 10-L
Brand: YOKOGAWA Pages: 20
YOKOGAWA UTAdvanced UT32A Technical Information preview
UTAdvanced UT32A
Brand: YOKOGAWA Pages: 3
TWR Lighting E-1DB2 Manual preview
E-1DB2
Brand: TWR Lighting Pages: 49
KELCO PG20 Series Instructions For Installing And Using preview
PG20 Series
Brand: KELCO Pages: 4
Castell KSSE User Manual preview
KSSE
Brand: Castell Pages: 7
AMALGAMATED INSTRUMENT PM4-RT8 Operation And Instruction Manual preview
PM4-RT8
Brand: AMALGAMATED INSTRUMENT Pages: 27
XINGDASHINE LBP-024 Manual preview
LBP-024
Brand: XINGDASHINE Pages: 3
DZ Custom Innovations ShiftSense Pro V2 Installation And Operation Manual preview
ShiftSense Pro V2
Brand: DZ Custom Innovations Pages: 8
hager RTQ520X Manual preview
RTQ520X
Brand: hager Pages: 10
AirPatrol Lite combi control Quick Start Manual preview
combi control
Brand: AirPatrol Lite Pages: 4

Brands by name

Popular brands

Load more brands