Texas Instruments Concerto F28M35 Series Technical Reference Manual Download Page 1389

Page: 1389 / 1655

www.ti.com

Ethernet MAC Register Descriptions

1389

SPRUH22I – April 2012 – Revised November 2019

Submit Documentation Feedback

M3 Ethernet Media Access Controller (EMAC)

Table 19-3. Ethernet MAC Raw Interrupt Status/Acknowledge (MACRIS/MACIACK) Register Field

Descriptions (continued)

Bit

Field

Value

Description

RXER

Receive Error

No interrupt

An error was encountered on the receiver. The possible errors that can cause this interrupt bit to be
set are: 1

• A receive error occurs during the reception of a frame (100 Mbps only).

• The frame is not an integer number of bytes (dribble bits) due to an alignment error.

• The CRC of the frame does not pass the FCS check.

• The length/type field is inconsistent with the frame data size when interpreted as a length field.

This bit is cleared by writing a 1 to it.

FOV

FIFO Overrun

No interrupt

An overrun was encountered on the receive FIFO.

TXEMP

Transmit FIFO Empty

No interrupt

The packet was transmitted and that the TX FIFO is empty.

This bit is cleared by writing a 1 to it.

TXER

Transmit Error

No interrupt

An error was encountered on the transmitter. The possible errors that can cause this interrupt bit to
be set are: 1

• The data length field stored in the TX FIFO exceeds 2032 decimal (buffer length - 16 bytes of

header data). The frame is not sent when this error occurs.

• The retransmission attempts during the backoff process have exceeded the maximum limit of 16

decimal.

Writing a 1 to this bit clears it and resets the TX FIFO write pointer.

RXINT

Packet Received

No interrupt.

At least one packet has been received and is stored in the receiver FIFO

This bit is cleared by writing a 1 to it.

19.6.2 Ethernet MAC Interrupt Mask (MACIM) Register, offset 0x004

The Ethernet MAC Interrupt Mask (MACIM) register is shown and described in the figure and table below.

Figure 19-5. Ethernet MAC Interrupt Mask (MACIM) Register

Reserved

R-0

Reserved

R-0

Reserved

PHYINTM

MDINTM

RXERM

FOVM

TXEMPM

TXERM

RXINTM

R-0

R/W-1

R/W-1C

R/W-1

LEGEND: R/W = Read/Write; R = Read only; -

= value after reset

«
...
1387
1388
1389
1390
1391
...
»

Summary of Contents for Concerto F28M35 Series
























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Concerto F28M35 Series

Reviews:

Related manuals for Concerto F28M35 Series

Brands by name

Popular brands

Texas Instruments Concerto F28M35 Series, Technical Reference Manual

Search results

Summary of Contents for Concerto F28M35 Series

Reviews:

Related manuals for Concerto F28M35 Series

Brands by name

Popular brands